Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
1. Turned off the cooling cycle and unplugged the refrigerator. 2. Removed all of the shelving and bottom basket. 3. Removed rear covering in the freezer section. 4. If frosted over, manually defrost coils with hairdryer. 5. Located original thermostat and after marking the wire locations cut the wires and removed the Thermostat. 6. Connected matching wires using a lighter to melt the wires together. Wrapped repaired wires with electricians tape. 7. Unable to install the thermostat in the recommended location (freezer is a tight fit) the new part was installed at the original location. 8. Replaced the rear cover and shelves. 9. Plugged in the refrigerator and set the cycle back to cooling. 10. Monitored freezer coils couple of days/weeks depending on how fast they freeze over (slots at bottom of cover) to validate if problem solved.
Temperature in both freezer and fridge sections to warm!
Dear Part-select, I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck Spokane, WA Houck Photo 509-723-3418 tomhouck1@comcast.net
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
I ept finding clumps of ice in try as though water was spilling over ice maker tray.
I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.
Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.
Unplug fridge, tilt back against wall to provice clearance to install new assembly. Used self starting screws to install. Used cordless drill with nutdriver to install assembly. Time to complete job-5 minutes
Needed to replace ice maker which had been making clicking noises as ice got jammed and then stopped working altogether.
Followed the instructions that came with replacement ice maker...was very clear and easy to follow and only took 5 minutes. I also watched the video sent via email with my order confirmation which was very well done and easy to follow. The only information that would have helped would have been a note to wait over-night for the ice maker to make ice as I thought I did something wrong when it wasn't making ice right away....waited until morning and had lots of ice. If I knew how straight forward and easy this was, I would have done it a lot sooner.
Ordered ice maker, watch video of how to. It takes less than 5 min. Installes just like the video. Loosen 2 1/4" Screws, lift ice maker up, unplug old unit, Reverse. Just make sure water tube is lined up when you install new unit and wire is tucked up out of the way. Mine did not really start making ice till the next day.
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!
Fridge would not cool at all, because the compressor was not running. Fan running, lights working, just no cool.
Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
