WRS3R3EW4 Westinghouse Refrigerator - Instructions

I had seen technician remove cover for warranty repair. If I had not I would have been in trouble... I removed tray exposing screws, removed screws and lifted off cover. I then pulled off connector to circuit board. I removed the three screws holding the broken dispenser part and removed it. The reverse was easy. The hinge cover was easy since I had learned to slide it forward FIRST (that's when I broke it). The shelf supports were tricky. The old ones would not come out. I sawed them off with a serrated knife and then picked the pieces out. Installing the new ones wasn't going well until I realized that I had to hammer the pegs in. Then they went right in.

I used the paint spatula to pry out the old part and then put in the new part and pushed in the holder with my fingers. Super easy.

Removed cover from top bracket with phillips sd. removed bracket with socket wrench; lifted door from hinge; removed remnants of old hinge from recess, this took a while because it had broken inside, eventually I used needle nose pliers to break it up and pull it out in three parts; installed new bearing hinge; reset door, and installed bracket and cover.

Easy!

I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks

I noted this repair as easy and it is if you know what you are doing. I read the repair stories on line and thought I would give it a whirl. I ordered the part on line and in my haste I didn't even consider that I would need to order by color. I have a black appliance. To my dismay when the part came it was white. While waiting for the part I had attempted to find the small screws that would allow me to get to the repair site as described in the sucessful repair stories. There was no screws visible. The water pan on my model does not come out and there didn't seem to be any way to get to the actuator without prying off the ice and water portion of the frig. I was afraid to take a screwdriver to my frig as I didn't want to scratch it up . I decided to just call a repair man. He came with the black actuator. I returned the white actuator. The repair took about 15 min. He popped off the front which I was afraid to try and took out the three tiny screws and replaced the part. The total charge was $167.00. $75.00 of the charge was for diagnosis even thought I told that no diagnosis was needed. Part cost was $19.99 and th rest was labor.

It was really easy! Just snap off the trim above and below the handle, unscrew the old broken one, and replace it with the new one. Then snap the trim back on above and below the handle.
My husband wanted me to call a repair service to come out and take care of this. It would have taken two visits, the wait time in between, and the cost for the visits and the labor. I paid a bit extra to have overnight delivery and fixed it myself in less than 15 minutes! I will definitely use PartSelect in the future!

1. Turned off water and unplugged refridgerator. 2. Removed the drip tray. 3. Removed the 3 screws under drip tray. 4. Pulled facing off the fridge. 5. removed the 3 screws at top of dispenser. 6. Pulled the dispenser out far enough to remove broken actuator. 7. Removed 2 screws holding broken actuator in place. 8. Removed broken actuator and replaced with new actuator. Re-attached everything in reverse. Be aware that there are two serial numbers on the labels inside the refridgerator. The one with the letters at the end tells the color of the refridgerator. I had to return and reorder. The company emailed me the instructions and that went well too.

take front panal off and unplug the electrectal tail to the front panal then unscrew the 4 hold down screws then take out broken part and then replace with new part and re-assemble front panal

My Frigidaire Drawer broke... I ordered the parts and installed it within 5 min. It took more time to remove the food and drawer then it did to install the pegs.

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

First I remove the water catch tray. Then I removed the three screws the hold the face plate on. ( You do have to slide face plate upward) I let that hang gently. Then I removed the three screws that hold the mother board in place, tilt the motherboard out to be able to see the back of the actuator. Remove three screws and flanges that hold actuator in place. Look at how spring is held in place before removing. Remove actuator, replace with new actuator set spring, replace screws and flanges, push motherboard back in place,replace the three screws,replace face plate with the three screws and replace catch tray. And your done!!!!

Took out the support and put back in the new one.

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

Replaced filter. Very quick shipping, was very happy to get is so soon.

Fridge came ice maker assy configured with an ice cream shelf to maximize space. I found this annoying becuase it blocked access to the ice maker controls and ice bin, which is useful for bulk access even thought there's a door front dispenser for ice. I recognized parts diagrams for a similar model and corrctly assumed they'd fit. So for $30 and an easy change I have the feature I wanted. Pretty cool.