WRS3R3EW4 Westinghouse Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Crisper support pins were quite tricky to secure
The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.
Parts Used:
-
JOSE from Miami, FL
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door hinge
-
james e from bellport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door wasn't opening and closing like normal
After taking door off, I found the door closure/hinge bearing was broke. I got manual out, looked up part number, googled it, and ordered the part from this website. Couldn't be happier!! My wife is really happy too, such an easy fix
Parts Used:
-
BRIAN from HIGH RIDGE, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Filter light indicated it needed to be changed
Just as the instructions showed. opened the refrigerator, removed the water filter cover. removed the old filter and installed the new one. Very easy to do.
Parts Used:
-
James from Abingdon, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper supports were broken
Drove pins all the way thru supports & then pryed support off. Tapped new supports in place. Watch the vidio on installing new supports. I probably wouldn't have been able to get the supports off without the trick I learned to just knock them on thru. Took all of 5 minutes to replace 4 supports.
Parts Used:
-
Fredey from Andrews, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original shelf broken
Replacement took about 10 seconds, just put it onto the holding brackets, pressed down and presto...DONE!
Parts Used:
-
William from Longs, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Chrisper Drawer Support was broken
Due to the nature of the support deisign and installation which was unusual I watched the video on how to extract the old broken support and install the new one, odering the new part was simple as the view privided in the parts section was specific and and easy choice to make, cost was very minimal and I received it the next day due to my being in close proximity to the shipping point, thank you and my crisper is very happy and so am I.
Parts Used:
-
Charles H from Beverly, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fridge door would not close automatically
I removed the door and replaced the broken hinge bearing with the new part and the door works great!
Parts Used:
-
Michael from Campton Hills, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic door cam broke
it was a simple fix, all i had to do was remove 3 small bolts from top of door, set door aside remove 1 screw that holds door cam in place, install new door cam.hole job took about 15 minute's.
Parts Used:
-
DAVID from HANCEVILLE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door made a clicking sound when opened...
Couldn't have been an easier. Removed the screw/nuts from the top of the fridge door that held the door in place and removed the door. Unscrewed the holder at the bottom, replaced both parts and put the door back together. It took me longer to get everything out of the fridge door than to replace the parts. EASY AS COULD BE!!!
Parts Used:
-
Kristopher from Branchport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing to shelves
-
Kendall from Brandon, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Actuator broken
-
Marcin from Carpentersville, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Made A Loud Clicking Noise When Opening
Took the door off,as per instructions,pulled the worn bottom bearing out, pushed new in and replaced door. The job was very simple and took about ten minutes. Also I received the part in two days after ording
Parts Used:
-
DONALD from CASTALIA, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I just simply inserted the bin
-
william from chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door made a loud noise upon opening
Removed the door , removed to old bearing , inserted the new. Works like a charm Thanks Marvin
Parts Used:
-
Marvin from Ocala, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!