WRS26MF5AQI Crosley Refrigerator - Instructions

Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attempt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.

Replacement of bins were simple the crisper cover supports were a little more time consuming since the manufactured piece were glued in. I used a tool that has a 30% tip and hooked the support and pulled in out part of the way and pulled the rest out with my fingers. All in all a simple job...I took the opportunity to do an addition cleaning of the inside of fridge with my extra time. Would also like to say that my parts were delivered within 24 hours of ordering them and the website made purchasing easy and no second guessing, since the model had an exploded version of all the parts available. Thank you

First removed the drip tray with a firm tug, Then removed the 2 screws to remove the trim, had to remove the board to get get to the connector. (there is a clip that holds the wire tight) connected the new ribbon cable and secured it with the clip, screwed the board back in and pushed in the other end of the cable. and screwed the trim back and the drip tray. surprisingly Very easy to do.

Simply slid glass into frame & it fit perfectly.

It's a good idea to unplug the fridge before you start. There are lots of wires and circuit boards in the area where you will be working.

To remove the in door water / Ice dispenser cover, remove drip tray, remove a couple of screws at the bottom and slide the cover up to release the tabs. There are a few scews holding the mechanism housing, remove them and gently pull the housing forward. You should be able to see the top iof the actuator. The actuator is held in place by 2 small metal plates, each with two small screws. Note the location of the return spring on the actuator arm! You will need to orient it the same way on the new actuator arm. Remove the screws and plates and lift out the broken actuator.

Put the new actuator in place and orient the spring as before. Replace the plates and screws and put everything back together.

If you have big hands, everything is a bit tight so, a small magnetized philips screwdriver or a screwholding screwdriver will make for easy work. I used a little scotch tape to hold the screw to the screw driver and it worked but, it took a few tries. Good Luck!

The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

Bought a new
capacitor.

The hardest part was figuring out how the front plate comes off. The tray will come forward when pried with a screwdriver. Then the top will come off but you will have to leave on due to attached wires. After that it was a piece of cake. Unscrew screws (6), remove small plates holding arm in place, remove arm, replace with new actuator, and close things up. As far as the valve, just take your time and, if needed, cut off pointed ends of tubings and push into new valve. Unplug color coded plugs and plug into new valve. Reattach valve to fridge and your done. We started everything up before attaching backing to make sure there were no leaks.

First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Followed the steps in the video on your site, really easy to do.

Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

take out screws front control panel ,then screws on left panel holding control unit. had to clean up plastic she got a little toasty. unhooked control unit replaced with new and reassembled. The real story is in your excellent web site easy to find exactly what I need and with prompt shipping, I was back in service quicker than having someone come out and repair.

Great Job
Jeff Baker

Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.