Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
ANGEL A - February 26, 2018
Verified Purchase
Simple installation.
Order contained both the ice and water actuators. Remove 3 screws along the bottom edge under the removable spill tray. Lift the bottom edge up and pull out. Separate the serial wires at touch panel's bottom edge. The touch panel frame should now be free. Remove the 3 screws around the icemaker circuit board. Both the ice and water dispenser tabs are held in by 4 screws and 3 tiny flat metal plates. If you seperate the water tube from the dispenser, be sure to clean the calc in and on the water tube. It is also a bear to get the tube back onto the dispenser. When replacing ice dispenser paddle, ensure ice chute flap is pushed open when paddle is depressed before you reinstall. If water dispenser paddle is removed ensure spring stays on place. Reverse steps to reassemble
★★★★★
★★★★★
James A - September 9, 2019
Verified Purchase
easy repair
easy repair no problem Just be careful with ribbon on circuit board
★★★★★
★★★★★
Joseph C - August 9, 2021
Verified Purchase
All is good
It was the correct part even though the part numbers didn’t match up . Watching the UTUBE video on how to replace it helped!
Happy customer!
★★★★★
★★★★★
Ken H - July 20, 2018
Verified Purchase
Water Dispenser Actuator
Manufacturer Part Number 241682002 was an exact match. Installation was a snap. Installation video was on YouTube and it helped a lot.
★★★★★
★★★★★
Valerie C - August 17, 2018
Verified Purchase
Pretty easy
Exact part even for my almond fridge, 2 day shipping was really 4 days; replaced ourselves with a little youtube help. Preplan the water hose reinstall- that's tricky!
★★★★★
★★★★★
Jim E - November 17, 2018
Verified Purchase
The repair was went fine
The repair part was right . I only gave you 3 stars because I got a defective part first time.
★★★★★
★★★★★
Kathleen E - August 14, 2018
Verified Purchase
Water dispenser works again.
We are pleased with the part. Only one complaint. It was very tricky to put it in. We would have enjoyed some instructions.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 15 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water actuator had broke off and water leaked from dispenser
The hardest part was figuring out how the front plate comes off. The tray will come forward when pried with a screwdriver. Then the top will come off but you will have to leave on due to attached wires. After that it was a piece of cake. Unscrew screws (6), remove small plates holding arm in place, remove arm, replace with new actuator, a
... Read morend close things up. As far as the valve, just take your time and, if needed, cut off pointed ends of tubings and push into new valve. Unplug color coded plugs and plug into new valve. Reattach valve to fridge and your done. We started everything up before attaching backing to make sure there were no leaks.
I (45 year old female) repaired this very easily. Pulled off the tray that catches water/ice overflow, unscrewed 3 screws, removed the ice/water panel from the freezer door, then removed 6 more screws, peeked to see how the original was installed slipped the new part into place and replaced all the screws, panel, etc. and done in less th
... Read morean a 1/2 hour (including cleaning parts not usually exposed for cleaning). Works like a charm!
Read less
Lyndalee from Scarborough, ME
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic paddle that actuates the ice dispenser broke off.
I followed the instructions that I pulled up online. It gave the basic instructions of how many screws that had to be removed, etc. etc, and basic instructions, but I did have to figure out for myself a couple of minor details. I am fairly handy and the project was not to difficult.
Jim
Jim from Sandy, UT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken water dispensor actuator
The repair was easy for me as I am very mechanically inclined. I did have a problem with the water actuator being a different shape then the original so I had ordered the ice actuator to replace also so they would match. The ice actuator matched the original so was unable to get the paddles to match in my door. It works fine but I don't l
... Read moreike the look of two different style paddles in my door.
The actuator on the water dispenser was broken and the water filter was leaking
The actuator was easy . . . just remove 6 screws (3 outside and 3 inside) and pull out assembly. The actuator popped out and I replaced it.
The water filter replacement was easy once I figured out how to use the quick connect fittings from the tube to the water filter assembly (see Youtube).
The repair was simple as described by another customer. One additional note, the water line is tight and can be difficult to remove. Extra slack is available under the fridge. Just push the slack up remove the water line. When the repair is complete reinstall the water line, pull the extra slack back from under the fridge.
Daryl from Alachua, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
part went in easy,water line was a problem .stainless steel screws should have been used, screws had to be drilled out.
first I drilled out two rusty screws. removed panel from door, disconnected water hose, installed actuator-water. fought to get water hose back in. replaced drilled out screws.
eva from titusville, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Piece of Cake!
Remove the drip tray to expose the 3 screws...remove screws and then 3 more screws to remove broken actuator and replace with new part.....very easy repair!
Julia from Saco, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
6 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water actuator broke
took off bottom plate to water/ice dispensor, removed three screws, took off front plate, removed three screws, unpluged water connector, removed two screws holding down water actuator where it pevits from and then replaced with new to find out the new part was off white vs white, does not look to good.....
Marc from Lafayette, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broke the actuator with a glass, and a door shelf by over filling it.
simple. removed the three screws on the front of the freezer door as shown on the parts list online, removed and replaced the part by removing two additional screws.The bin was just slipped in.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Andrea
November 6, 2019
Looking for the actuator (paddle) for the water dispenser (not ice dispenser) for a Frigidaire side by side fridge model plhs237zab5. Thanks.
For model number PLHS237ZAB5
Hello Andrea,
Thank you for your question. The correct actuator for your model is under part PS8760537. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Ed
June 30, 2021
Water paddle actuator part number item number 24
For model number GLRS64ZEQ6
Hello Ed, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS8760537. This kit includes both the water and ice actuator. we hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Gary
May 25, 2022
Looking for a water dispenser actuator (not ice dispenser ) Frigidaire Model # GLRS267ZAQ1
I would require colour BISQUE to match fridge.
For model number GLRS267ZAQ1
Hello Gary, thank you for your question. The Bisque color is no longer available. There is black only. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lizettte
September 22, 2023
I just need the water paddle and the ice paddle - i don't need the ice cover
For model number PLRS267ZAB6
Hello Lizettte, thank you for the question. The paddle is not sold separately. You will need to replace the whole dispenser actuator kit, part number PS8760537. Good luck with your repair!
Was this helpful?
Thank you for voting!
Bob
April 21, 2024
I broke the water paddle for the dispenser. I looked at your
Schematic and it’s part number 24. When I pull up the part it is exactly as 24A. Is part number 24 correct for the water paddle?
The ice paddle is not broken. I just need the water paddle.
For model number PLRS267ZAB7
Hello Bob, thank you for your question. The Dispenser Actuator Kit includes both the water and ice actuator. We hope this helps.
Was this helpful?
Thank you for voting!
Andrea
November 5, 2019
Does this kit come with the actuator (paddle) for both the water dispenser and ice dispenser? I need the one for the water dispenser (but i'll take both if that's the way it comes). Just that the photo looks like the ice dispenser only. Thanks!
Hi Andrea, thank you for your question. The photo would be correct, it is just your ice paddle. If you need the water that would be a different part. If you would like to resubmit your question with the model number of your appliance we can find that part for you. Thank you.
