WRS23MW3AWF Westinghouse Refrigerator - Instructions

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

First removed food from the refrigerator door.

Second removed plastic cover plate and metal plate assembly from top of door.

Third lifted door of metal pin on bottom.

Fourth removed broken closer plate and replaced
with new closer plate.

Set door back in place.

Re secured the metal plate and plastic cover plate.

Replaced the door shelves and food. DONE.

First I looked up and called Fridgedaire. They were absolutely no help at all. No diagrams and no intelligent help.
When I found your site there was an IPB (Illustrated Parts Breakdown) diagram that helped me find the parts that I suspected as being the problem. When I found them and added them to my cart I found several comments from people who had the same problem and the same remedy to the problem. I ordered the parts, I could have got away with just replacing the door closure bearing, but I figured that the prudent thing to do while ordering parts and disassembling the door was to replace both.
I was extremley pleased with the parts service as within three days of ordering the parts they were at my home and the repair was completed.
The repair was very easy. Removed the items from the door storage, removed the upper hinge pulled the door, removed the door stop, replaced the door closure bearing reinstalled the pieces and then reinstalled the door. Piece of cake. Spent more time getting the tools together and emptying the items stored on the door then replacing the parts.

Fridge has Ice & water in Door.
Slide bottom plate out.Remove three screws
across bottom.
Remove two screws that holds a circut board.
pull the water hose off and remove board.The hose is a little tricky getting back on.

remove two screws that holds two little plates and remove old part.
Reverse prosedure to put back.

I remembered to unplug first. took the little cover off on the bottom, unscrewed the 3 screws. then just held the base that the fan is on and pulled rite off, pushed the other one rite on. it took me five min, i want to say thanks to parts select, had the part, fast shipping, great job, thank you.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Followed video instructions which were to unplug refrigerator, on lower back use screwdriver, loosen 4 screws, take off plastic cover, pull out fan, replace with new fan, replace cover and 4 holding screws, plug in refrigerator. I am female, 77 years old and if I can do it, anyone can.

Twisted replacement bulb into place easily. Let there be light!

First I cleaned out the side door then, removed the three screws on top of the door. Lifted the door off and set it carefully on a kitchen mat.

I had to use the pliers to remove the existing bearing hinge as it had disintegrated in the door. Once it was out the new hinge slid right into place and I reinstalled the door. I had help with the door. It’s much easier with two people to get proper alignment and to hold it in place while you reattach the screws.

I would have to say the hardest part of this repair was cleaning out the refrigerator.

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.

very easy to do. just snap into place

Slid the shelf in place!