WRS23MF5ASJ Westinghouse Refrigerator - Instructions

1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

unplugged the old one and pushes in the new one DONE IN LESS THAN 6 Min.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Took out the old one and pushed in the new one. Easy, peasy.

I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.

I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Slid the new one in easy !

We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

Snap out and snap in.

after watching the video I followed to the tee used the screw driver tapped out the old peg and removed the stem in minutes I was tapping in the new parts

Push the button on the right side of the ice maker filter compartment which releases the old filter. Just pull old filter out and slide the new filter all the way in. Be sure and mark on the new filter the date that will be time to change the filter again. I ordered the filter on one day and received the filter in the mail the next day and I had not paid extra for overnight shipping.

The repair was easy. After looking at the diagram and locating the part need i just ordered it. But I wish I had taken the door off before ordering as I really need a second part. So resulting in extra shipping cost. Parts that were needed were 240328201 and 240457702. Tks Jim