WM2487HWM LG Washer - Instructions

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

The drawer was knocked off the top of the washer and hit the floor. One of the two plastic strips in the back that fit into the channel to insert the drawer broke off. Super glue would not keep it together, so I ordered a new drawer. So glad this site had it...LG does not sell replacement parts, and I did not want to buy a new machine for such a minor problem!

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Replaced the 4 valave unit and single hot water valve at same time. Unplug unit, remove two plastic tabs on back of washer, push on top from front to losen. tur off both water valves, remove two screws holding valves in place, mark with tape which hose goes to which vavle, < back left, back righ, front left, front right, and write in electrical plugs the same. Hot water vavle is by itself, mark it anyway>. install new vavles, replace hoses, and eletrical plugs on top. Make sure clamps are all the way forward and tight! > leave top off. turn on water and electrical, run one short cycle to check for operation and leaks, if ok, replace top and back screws. Simple job, saved me $375.00 doing it myself.

Basic skill

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

greate very easy and the parts fit awsome the shiping was fast and easy very satified

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

Replaced rotor assembly by removing the back panel off the washer. Removed center bolt to be able to take out roto assembly. Magnets made it a little resistant, but with a little wiggling came off fairly easily.

I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!