Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WM1812CW > Parts

WM1812CW LG Washer - Parts

All parts for the LG Washer WM1812CW

Below is a list of all parts for the LG Washer WM1812CW - Residential WASHER. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the WM1812CW
1-14 of 88
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$69.64

Drain Pump and Motor Assembly

The drain pump and motor assembly may also be known as the washer drain pump, and is a part for your washer. The function of this assembly is to help expel water from the washing m...

$22.05

Water Inlet Valve - Hot

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

$51.91

Water Inlet Valve - Cold

The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and ...

$46.54

Switch Assembly,Locker

The locker switch assembly is a part for your washing machine and tells the washer that the door is closed and locked into place. If the switch has shorted out and not locking, it is no longer delivering the message to the machine and it will not latch into place. If you find that your door will not close, open, or start, it is more than likely an issue with the locker switch assembly. The switch is located behind the front panel. You will need to remove the gasket to reach the switch.

$13.88

Locking Pin

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in...

$17.98

DAMPER ASSEMBLY,FRICTION

Sold individually.

$26.42

BEARING,BALL

This bearing, or ball, is a genuine OEM replacement part for your washer. The bearing allows the tub to rotate smoothly. Replacing this part can be helpful if your washer is extrem...

$11.85

Pump Filter

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

$11.85

Pump Casing

This part connects to the drain pump and motor.

$4.35

Cap,Drain Hose

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

$11.85

Gasket

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. ...

$22.05

Bearing,Ball

Tub bearing supports the spin basket shaft at the bottom of the washer tub. If your tub bearings are damaged or faulty, the washer will run noisier than usual during the spin cycle. Tub bearings are meant to ensure free movement of the wash basket. In top-loading washers, there will typically be two bearings: one where the shaft connects to the clothes basket and one at the bottom or transmission input. In front-loading washers, both bearings will be supporting the clothes basket shaft at the back of the outer tub. The bearings have an outside diameter of approximately 3 inches.

$90.79

Spider

The spider, or rear tub support, is located behind the outer tub of your washer, and provides support to the outer tub. It has 3 legs and each measures approximately 10 inches long...

$11.85

Gasket

All Parts for the WM1812CW
1-14 of 88