Models > WGD9450WW1 > Instructions

WGD9450WW1 Whirlpool Dryer - Instructions

All Instructions for the WGD9450WW1
556 - 565 of 565
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old lint filter had holes in it.
removed old one installed new one.
Parts Used:
Lint Filter
  • John from Massanutten, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No heat
Just like the instructions. Piece of cake.
Parts Used:
Igniter Kit
  • Randal from Fowlerville, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Noisy/Rattleing Tumbler
First i did some research on the internet approx.1yr ago.Just in case any problems like this or any other kind of problems should arise which it did.The whole thing is Easy all you have to have is some basic knoledge of how things work.All of this came "OFF" in (4) sections.After installing everything back it was as "Quiet"as the day we purchased it.Good for another 5yrs.Retired welder & "J.O.A.T.Julian San Antonio,Texas
Parts Used:
Dryer Repair Kit
  • Julian from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
dryer wasn't heating
Followed the parts select You tube video. Was helpful. Note the Ignitor kit is very sensitive. We didn't need an ignitor right now but purchased one in case the other 2 parts didn't help the problem. We took the ignitor ( wrapped in a bag) out of the packaging and it snapped in half without even touching the sensitive end. Note handle with extreme care.
Parts Used:
Dryer Radiant Flame Sensor M Series New Style Coil Kit
  • ERIN from RED WING, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer was throwing a E1 Error
Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).
Parts Used:
Thermostat, Internal-Bias
  • John from Indian land, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Door latch was broken
This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.
Parts Used:
Door Catch Kit
  • William from Champaign, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door would not close
Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.
Parts Used:
Door Catch Kit
  • Daniel from Stratford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Felt wears on the dryer lint screen
No repair. Just replaced the screens in the dryer and they slide in and out to clean. The felt gets worn fast.
Parts Used:
Lint Filter
  • Judy from Cloverdale, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Long Time Drying
Un plug dryer . Take off dryer door . Remove front panel by pulling out. Remove 2 screws holding coil bracket . Remove electrical connectors ,remove 2 coils . Install 2 new coils same as old ones connect elect. Wires replace coil holding bkt. Unplug flame sensor . Remove 1 screw . Replace old flame sensor with new plugin elect. Connector replace in reverse wala ,,,alldone button up dryer plug in dryer . . Good to go.
Parts Used:
Dryer Radiant Flame Sensor M Series New Style Coil Kit
  • ALEXANDER from HUNTLEY, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
lint filter coming apart
removed old one, threw it away, and inserted new one.
Parts Used:
Lint Filter
  • Alan from Oklahoma City, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WGD9450WW1
556 - 565 of 565
Back to Top