Models > WGD9400ST1 > Instructions

WGD9400ST1 Whirlpool Dryer - Instructions

All Instructions for the WGD9400ST1
556 - 570 of 578
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Felt around the Lint Filter was loose and would not stay
Took out the old one and put in the new one.
Parts Used:
Lint Filter
  • Janice from Central Lake, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
It woud begin to heat and dry clothes then it would stop heating before the clothe dried.
Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.
Parts Used:
M Series New Style Coil Kit
  • Thomas from Bath, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would heat up at startup but not stay hot for long. Took forever to dry clothes. Started smelling a very slight gas leak about a week before the problem started. I suspect the coils have been going lame for quite some time. The dryer heats up like it was new.
Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.
Parts Used:
M Series New Style Coil Kit
  • dan from Orinda, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer door kept popping open
following the repair video made it super easy. thanks!
Parts Used:
Door Catch Kit
  • vangelis from rosemead, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
flame out
easy as pie !
Parts Used:
M Series New Style Coil Kit
  • john from glen head, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer worked but did not heat
Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.
Parts Used:
Dryer Radiant Flame Sensor
  • Steven from Garden City, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
very noisy
followed the you tube video, came apart ok, very bad lint problem. Vacuummed out extensively. Made repairs, very straight forward. Back together ok, still noisy but not as bad. May be the fan.
Parts Used:
Dryer Repair Kit
  • Christopher from Momence, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
couldnt find this model dryer on the whirpool part on their site
Found this part on your site very EZ bought it you shipped to my door got it when you said it would be here open it installed it propblem over glad i found you guys will use again Very good website Keep up the good work THANK YOU
Parts Used:
Lint Filter
  • clyde from Harrisburg, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
latch inside door popped out
Order one new latch, receive 2 spares. Pushed new latch in, re oriented the catch. was done in less than 5 min
Parts Used:
Door Catch Kit
  • zachery from snoqualmie, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The Dryer would make a squealing noise like a toddler while running.
We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.
Parts Used:
Idler Pulley with Bracket Idler Pulley
  • Ann from Phoenix, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer cycles but will not heat
removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.
Parts Used:
M Series New Style Coil Kit
  • daniel from mercedes, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer door was difficult to close
One small part of the hinge broke and made it difficult to close the door. Purchased the part, $91 with shipping, from PartSelect. It arrived within the week. Installed it within minutes. End of story!
Parts Used:
Door Hinge
  • Lora from Murrieta, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No flame
when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.
Parts Used:
M Series New Style Coil Kit
  • Rafael from SAINT PAUL, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Old lint filter had holes in it.
removed old one installed new one.
Parts Used:
Lint Filter
  • John from Massanutten, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No heat
Just like the instructions. Piece of cake.
Parts Used:
Igniter Kit
  • Randal from Fowlerville, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WGD9400ST1
556 - 570 of 578
Back to Top