WFW9500TW02 Whirlpool Washer - Instructions

Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately $150.00 bucks in repair service fees.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Everything went great from order to done. Very happy

Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

After receiving the hinge and screws, I watched the on line video at the website. I removed the door and hinge from the washer, removed the hinge from the door and re-installed the new hinge. The entire process took less than 15 minutes and reattaching the new hinge to the machine was a breeze. The replaced hinge is smooth as silk and all is back on line. Great service from the crew at this site. Shipping was very quick (ahead of the scheduled arrival) and the CSR was very cordial and professional.

Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.

Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.

It was so easy my wife replaced the part.

I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.

Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd

Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.

Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_

I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.