WF350ANGXAC Samsung Washer - Instructions

First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Strip clean and replace

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.

Removed top cover. Manually opened door through top cover opening. Removed 3 screws at front holding assembly. Removed 3 harnesses attached to assembly. Replaced with new assembly and screwed back in. Replaced harnesses. Certainly an easy DIY job.

The product came on time and was perfectly rapped , it took me 15 mins to install after watching you tube videos on front loader washer . I was happy I didn't have to call a service man in . . . .

Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!

Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!