Models > WDF530PAYB0 > Instructions

WDF530PAYB0 Whirlpool Dishwasher - Instructions

All Instructions for the WDF530PAYB0
271 - 280 of 280
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clean light was flashing and that was only light that worked.
We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.
Parts Used:
Dishwasher Heating Element
  • Angela from Cookeville, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Heat element broken
Removed unit from counter. Replaced element.
Parts Used:
Dishwasher Heating Element
  • Dana from Palm City, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Installing a new dishwasher in a remodeled Kitchen
I remodeled my kitchen with new cabinets. In order to better utilize cabinet space, I located the dishwasher away from the sink, which means that I had to have a longer drain hose. The store I purchased the dishwasher from didn't have a longer hose, so I went online and found it on this website. Thanks for the quick shipment. I ordered it using standard delivery and received it in less than three days. I have book marked this website for future use.
Parts Used:
Drain Hose
  • Maxie from Bridge City, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Latch broke on dishwasher door
I removed the screws on the inside of the door. Removed panel from the outside. Disconnected the power wires to the panel. Disconnected the wires to the latch switch. Removed the latch assebly. Put new assembly in place. Connected swtich wire. Connected panel wire. Put panel back on dishwasher door. Installed panel retaining screws. Job Complete!
Parts Used:
Door Latch - Black
  • david from escondido, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Heater Element burned out
Disconnected the power. Removed the dishwasher mount screws from under the counter. Slid the Dishwasher out. Removed the two wires. Loosened and removed the two heater support nuts. Removed the heater element from inside the dishwasher. Placed the new heater element inside. Tightened the nuts. Attached the wires. Pushed the dishwasher back in place. Replaced the under-counter support screws. Reset the diagnostics message on the dishwasher front panel (This may not be necessary for some) - (Press HI TEMP > AIR DRY > HI TEMP > AIR DRY). All works great. Thank you PartSelect.com for fast shipping and great pricing.
Parts Used:
Dishwasher Heating Element
  • Travis from Los Angeles, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
cap was not tightened correctly melted on heating element
put new on and tightened correctly -was nice to get the right part the 1st time !
Parts Used:
Rinse-Aid Dispenser Cap
  • Ronald from Pearland, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water leak
replaced gasket
Parts Used:
Dishwasher Door Gasket with Strike - Black
  • douglas from Clyde, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dishes were not dry, flashing lights.
Pulled the dishwasher out, removed 2 wires and 2 plastic nuts, removed old heating element, installed new heating element, applied nuts, connected 2 wires pushed the dishwasher back in, drank beer (Per instructions on email - really liked).
Parts Used:
Dishwasher Heating Element Rubber Washer
  • Randy from Port Byron, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Not drying
As directed online
Parts Used:
Dishwasher Heating Element
  • Todd from Huntsville, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Water dripping from lower corners
Removal and replacement of the gasket required no tools and took very little time. However, this did not solve the problem. I called in a repairman who determined the issue was the washer was not filling to the proper level. The control board was replaced and the problem was solved. This also quieted the washer a lot in that the pump was no longer sucking air.
Parts Used:
Dishwasher Door Gasket with Strike - Black
  • William from Mt Pleasant, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WDF530PAYB0
271 - 280 of 280
Back to Top