All Installation Instructions for Whirlpool Dishwasher WDF510PAYS2

rinse aid dispenser leaked

cap was replaced

Parts Used:

Rinse-Aid Dispenser Cap

Roger from St. Clair Shores, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Dishwasher leaking from door

Old gasket was broken in places and old. Installing the new one was easy- no tools required. Just pull out the old one and press in the new one. Washer still leaks because door does not close all the way- need to figure out how to get it to shut tight. Maybe the latch is loose or worn.

Parts Used:

Dishwasher Door Gasket with Strike - Black

Charles from Lehi, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Detergent rinse aid dispenser door would not close, latch broke.

Rmoved door skin to dishwasher. Then remove screws on the back side of the detergent/rinse aid despenser. Remove old despenser and install new one.Install all screws. Took about 15min. Very easy fix.I recieved the part very rapidly , Thanks partselect.com.

Parts Used:

Detergent and Rinse Aid Dispenser

Shannon from wichita, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Heater Element burned out

Disconnected the power. Removed the dishwasher mount screws from under the counter. Slid the Dishwasher out. Removed the two wires. Loosened and removed the two heater support nuts. Removed the heater element from inside the dishwasher. Placed the new heater element inside. Tightened the nuts. Attached the wires. Pushed the dishwasher back in place. Replaced the under-counter support screws. Reset the diagnostics message on the dishwasher front panel (This may not be necessary for some) - (Press HI TEMP > AIR DRY > HI TEMP > AIR DRY). All works great. Thank you PartSelect.com for fast shipping and great pricing.

Parts Used:

Dishwasher Heating Element

Travis from Los Angeles, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

cap was not tightened correctly melted on heating element

put new on and tightened correctly -was nice to get the right part the 1st time !

Parts Used:

Rinse-Aid Dispenser Cap

Ronald from Pearland, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

water leak

replaced gasket

Parts Used:

Dishwasher Door Gasket with Strike - Black

douglas from Clyde, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Dishes were not dry, flashing lights.

Pulled the dishwasher out, removed 2 wires and 2 plastic nuts, removed old heating element, installed new heating element, applied nuts, connected 2 wires pushed the dishwasher back in, drank beer (Per instructions on email - really liked).

Parts Used:

Dishwasher Heating Element

Rubber Washer

Randy from Port Byron, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

Not drying

As directed online

Parts Used:

Dishwasher Heating Element

Todd from Huntsville, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Water dripping from lower corners

Removal and replacement of the gasket required no tools and took very little time. However, this did not solve the problem. I called in a repairman who determined the issue was the washer was not filling to the proper level. The control board was replaced and the problem was solved. This also quieted the washer a lot in that the pump was no longer sucking air.

Parts Used:

Dishwasher Door Gasket with Strike - Black