WDF310PCAS0 Whirlpool Dishwasher - Instructions

Shut off water,power. disconnect water line,electric,drain.Pulled dishwasher out,laid dishwasher on it's back.Unplugged electric on pump,twisted pump out.Installed new pump and reinstalled dishwasher.

it was just a matter of snapping the new assembly in place.

Pulled the old one off and inserted the new one. Any woman can handle this one. :-)

Watched the "how to" video, then did the job. All in 15 minutes.

Repair was easy. After readjusting the dishwasher so that it wasn't leaning forward (it still leaked) I replaced the Door Gasket. Pulled one end out about 2 ft and pushed in the new one as I pulled the old one out and pushed the new one in. Came out and went in easy, just used a big screw driver to slighting push the new gasket in to make sure it fit snug. Fit, Form & Function was all correct. Works like a sharm, no more leaks and door does fit snug when closing. All good.

Repair was simple. Pulled out the old gasket and pushed in the new one.

I first purchased the door assembly because the solenoid was fried. That was a fairly easy installation. Unfortunately the door still didn't open. I then purchased a new Electronic Control Board. The installation was again fairly easy. After killing the power I removed the (10) Torx door fascia screws. Then I removed (2) Torx screws holding the control assembly on. Support this assembly to reduce strain on the wires. Slip the two tabs on the left side of the board that retains it. Carefully remove all of the plug connectors. Then reverse the entire procedure and test.

Ordered the gasket on line. Received gasket in 3 days. Removed old gasket by pulling out in one piece. Pressed the new one in with my fingers and it fit perfectly and now have no leaks. Very easy fix.

put new one in

Old gasket was broken in places and old. Installing the new one was easy- no tools required. Just pull out the old one and press in the new one. Washer still leaks because door does not close all the way- need to figure out how to get it to shut tight. Maybe the latch is loose or worn.

turn off power---open door--remove 12 screws holding front door panel on--remove door panel--tape upper protection cover in place--remove 2 wire plug to dispenser-- remove 6 screws holding dispenser--remove dispenser--re assemble in reverse directions above

we stretched the gasket and reused the old part. then we ordered a new dishwasher

I replaced the door gasket. This was easily done. First I removed the old gasket by simply pulling it out, no tools needed. The gasket is simply resting in a slot. Then I installed the new gasket by pushing it into the same slot, after I had thoroughly cleaned it with vinegar. I did not need to trim the gasket at all; it fit perfectly.

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.