WBXR1060T5AA General Electric Washer - Instructions

I found the diagram in your website, identify the problem, order the replacement part and replace it in 10 minutes. Great deal, thanks.

Watch how to fix it on You Tube. Order the part I needed and fixed. Real simple. That is it.

I used the video instructions sent to my email and everything worked perfectly as instructed.

It was only a matter of putting a new knob in place of the broken one. No tools required.

Unplug washer, turn off water and remove the supply hose, remove 5 torex screws remove panel disconnect two wire plugs remove 2 philips screws squeeze hose clamp remove old valve install new valve reversing directions

Unplugged power cord and shut off water supply. Then removed both water hoses from the dual water inlet value using adjustable pliers. Next removed four (4) star screws on top of the control panel. This required the purchase of a #20 torq screwdriver from sears costing $3. 99 Plus tax etc. Once the top panel lifted upward and to the left I was able to unplug both electricle connections on the water inlet vlaue. Next unscrewed two phillips head screws holding the water inlet value in place. Installed the new water inlet value in reverse of above. Time to complete was 22 minutes. Very easy repair to accomplish.

We were lucky, the agitator came off on its own. Removed the coupler which cracked when a sheet got stuck underneath it! Replaced coupler and new screw/nut combo, popped on agitator. That easy.

WATCH THE REPAIR VIDEO! I followed the easy instructions and replaced the water level pressure switch in no time. It was very easy to do!

Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.

My 45 year old son did it in the shop, and it only took a short time before we were washing clothers again, and no water on the floor. The part came through the day after I ordered them. Thank you very much

I replaced the water level pressure switch but that did not fix the problem. I tried to replace the pressure tube with some rubber tubing from the hardware store but that did not fix the problem. I replaced the tubing with the correct pressure tubing for PartSelect and now it seems to be working fine. I think the old tubing had a small leak in it I could not detect and the hardware tubing was not exactly the same as the manufacturer part. Anyway it was still a lot cheaper than a new washer. Thanks for the parts and the videos, you made it a do it yourself job. John

The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.