W246 Jenn-Air Wall Oven - Instructions

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

Placed new knob directly on post. No problem

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.

My 31 yr. old grandson very carefully took the whole door apart. Took out the broken window and put the new one back in. He was very careful to put every screw back in the original hole. It took him exactly one hour.

In my 26 year old oven the screws to remove the element were extremely difficult to remove, but with 6-10 applications of Liquid Wrench and brute strength we finally did. We were a bit concerned with the insulation that was protruding but used electrical tape to secure the wires to the leads for good measure. All was successfull. I love my Jenn-Aire double oven!

Old (broken) knob was gone, so wife oriented new knob over selector shaft, and pushed onto shaft!! PROBLEM FIXED!!!!! No fuss, no mess - just as good as new!

We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.

I watched the youtube video that was provided by this website on my computer while doing this repair step by step. It was a snap!