W206W Jenn-Air Wall Oven - Instructions

Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

Placed new knob directly on post. No problem

For those with an older Jenn-Air, this range has stood up under the test of time and is still in good condition. We even called Jenn-Air for the parts and they no longer carry the oven door seal for this make. Thank you PartSelect for carrying the seal. We did call in a repair man and are glad we did as taking apart the door was quite involved. We were very blessed to locate a repair man who did Jenn-Air and are very pleased with the repair.

removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.

Left door attached to range. Took out all screws on door to get to the door seal. Cleaned parts as I went. Took out old seal and laid new seal in. Had to get two more hands to hold the parts and glass together while screwing it back together. Only hard part was remembering which screws went where. Looks and works like new. So glad I did it, as it has needed it for a long time. Easy even for a 70 year old female. PartSelect had the best price even with shipping. Thanks

Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.

My 31 yr. old grandson very carefully took the whole door apart. Took out the broken window and put the new one back in. He was very careful to put every screw back in the original hole. It took him exactly one hour.

In my 26 year old oven the screws to remove the element were extremely difficult to remove, but with 6-10 applications of Liquid Wrench and brute strength we finally did. We were a bit concerned with the insulation that was protruding but used electrical tape to secure the wires to the leads for good measure. All was successfull. I love my Jenn-Aire double oven!

Decided since the glass was broken I might as well replace the door seal. Getting the door off and on was the most difficult part of the process as the door hinge springs are quite strong. Remove screws on the hinge. Slide door off hinges. The hinges will close rather hard. Remove screws along the outside, then inside. Keep all the screws in some order as they are different sizes. More time to clean the door than actually installing the glass and seal. Re assemble. Trick to getting the door back on is to open the hinge spring to the broil position and place a thin screwdriver in an opening in each to keep in an open position. Slide door down to the srewdriver stop and then fully open. You can then slide the door fully onto the hinge, replace the hinge screws. Easy ,for a simple housewife.