Quick Question!

Have you ever purchased from PartSelect.com before?

Models > VBXR1070W0WW > Instructions

VBXR1070W0WW Hotpoint Washer - Instructions

All installation instructions for VBXR1070W0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the VBXR1070W0WW
61-75 of 588
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

agitator stripped

  • Customer: Ron from Benton, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 12 of 15 people found this instruction helpful
removed the old one and replaced with new

Agitator not agitating

  • Customer: Troy from Porter, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 13 of 18 people found this instruction helpful
Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

Washer machine didn't get water.

  • Customer: Eduardo from Borrego Springs, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 10 people found this instruction helpful
I remove three screws on top of the washer, moved the cover of the machine in order to get access to the water valve, and then desconnected the two solenoid of the valve,and removed two screws that hold the valve with the frame and installed the new valve in same order a took the old one.

Water was leaking

  • Customer: Christine from Tempe, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 10 people found this instruction helpful
My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.

Hose and clip were broken in moving

  • Customer: DARYLD from SCHOFIELD, WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 17 people found this instruction helpful
The parts were here in 3 days and the repair went very quickly .Quality item would do business again.

Waher would not spin wet clothes.

  • Customer: Gerald L. from Las Cruces, NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 11 of 14 people found this instruction helpful
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

loud noise upon aggitation

  • Customer: Robert from Covington, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 14 people found this instruction helpful
replaced Tub dampeners Straps.

Inner tub base hub disintegrated

  • Customer: Doug from Kannapolis, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 10 of 11 people found this instruction helpful
I had to take the washer outside since there was no room to work on it in the laundry room. The extra space allowed me to spread out the parts, use the garden hose to clean and have light enough to take digital pics of the wiring before I disconnected them to remove the upper panel.

Removing the upper retaining ring for the tub was simple with only 4 screws. The agitator pulled right up and out. The nut cover/agitator anchor removed easily with one bolt.

The tough part was the inner tub base hub nut that I could not get off. Another user had commented on how they had to chisel the nut off and that was the best advice. I used my air chisel on either side of the nut and it was pretty quick to get off - within 3 min. If I hadn't read that I wouldn't have ordered another nut to replace the one I chiseled off.

The diagrams and repair stories really made the difference. Cleaning and reassembling was done within about an hour - cleaning the 11 years of soap scum at least an hour total before and after replacing the parts.

Washer tub fell sideways

  • Customer: Chris from Tampa, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 12 of 17 people found this instruction helpful
Only took 2 days to ship. Took the screws out of the bottom rear panel to gain access to bottom of tub. Next pushed the two hidden tabs with flat screwdriver in the front to gain access to the top of tub, they are located straight inline with each side of the washer lid in seam between the top panel and the front side panel of washer. Then installed the new suspension rod and reassembled. You can find online videos that show how to disassemble appliances if you're not sure how to get them apart for repair. My first appliance repair was easy to do and saved a lot of $$$ vs paying for repair or purchasing a new unit.

the bottem of the tub

  • Customer: michael from warwick, RI
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable), Wrench set
  • 10 of 12 people found this instruction helpful
at the bottom of the tub their is a mettal peace witch holds the tub to the transmision witch is made of zink(aka junk metal or zink+tin)witch broke stoping tub from sping the clotes dry so atfer odering the new part and nut..
and finding out that it is a LEFTHAND nut made of alumanum
taking a small drill bit 1/8" and drilling the nut to weakin it making it brake able then cleaning the treds up
the new part fit right in the tufest part was hold the trans still to get the nut on tightenuf to hold the tub

washer overflowed while running

  • Customer: Michael from Katy, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 10 of 12 people found this instruction helpful
First, I removed the four screws to expose the control panel. Then I removed both of the wiring connections on the switch, unscrewed the two screws holding the switch, and removed it carefully. Take the time to look at the old switch because it does not simply lift off the panel. It has a sliding lock to keep it in place on the panel and you must be careful when you remove it or install a replacement. The new switch installed easily, so I reconnected the power and started the washer. Bingo!

Purchased used washin machine w/o drain hose

  • Customer: Daniel from Oxford, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 9 of 9 people found this instruction helpful
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Overflowing washer

  • Customer: Paul from Perrysburg, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
Unplugged the washer and unscrewed the hot and cold filler hoses from the back of the machine. Removed the 6 screws holding the top together. Unscrewed the 2 water valve mounting screws. Pulled off the electrical wires from the leads. Unclipped the water feed hose clip. Reattached everything to the new water valve in reverse order. Put the screws holding the top panel in place back in.

For good measure, I also replaced the drain hose since I had noticed a little leakage there. Two screws and a little twisting and pushing was all that took.

Then I hooked everything back up and it worked like a charm. Finally, I went out to dinner with my wife on the money I saved!

Washer won't drain water

  • Customer: Ben from Lake Forest, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set, Wrench (Adjustable)
  • 10 of 13 people found this instruction helpful
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

Old one had developed rough or little jagged edges on the side

  • Customer: Ganesh from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
Just used hands to pry open the old agitator from the washer. If one angle does not work try another and go in a clockwise direction. The new agitator had a new coupling at the bottom, so I needed something to push it out from the top, found a long metal rod and easily pushed it down and out. Verified that new coupling was exactly the same as the old one. The old one was good so I just pushed the new agitator down on the old coupling and it worked fine.
All Instructions for the VBXR1070W0WW
61-75 of 588