TGO356BFD3 Frigidaire Range - Instructions

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

First I removed the metal burner covers and then placed a thick towel over the top part of the oven to prevent scratching and in the event the glass fell, it towel would prevent breakage. I proceeded to loosen the screws holding the glides on both sides of the glass. The overhead glide attached to the upper oven bottom was the issue in extending the time to replace the lamp. All screws came out easily except one. One screw had become rusted from the moisture released during years of cooking. The head of the screw stripped inside the hole so I had to use a drill bit to loosen the screw. Due to dull drill bits, it took around 15 minutes before I was able to grip the head of the screw with a pair of pliers and screw it out. The treads of the rusted screw were undamaged so replacement would be no problem. The overhead glide hood was removed allowing me to remove the glass. The lamp was removed by a simple twist (flourescent bulb) and the replacement inserted with a half twist, a small click sound and a visual inspection indicated the lamp was installed. The overhead hood was reposition using two screws, one on each side. The glass was positioned to cover the lamp and the light switch was turned to the on position to test the light, the lamp turned on. Following the lamp test both side glides were fastened with all screws. The overhead hood was secured with the remainder of the screws. A new metal screw was used to replace the damaged screw. All the screws were checked and tightened where needed. The replacement knobs took seconds to install on the oven.

snapped the new piece of plastic in its place and ta da, its fixed.

Put a new one in.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

It was a replace racks not repair. No problem

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.