TDB647RHB0 Tappan Dishwasher - Instructions

I took out 6 screws, the face plate just hung down. Make sure the breaker is off. there were two screws that held the switch and handle in place took those two out. Disconnected the four wires on the microswitchs and placed them on the new handle. Put the diswasher back together. Turned breaker on and worked great. But it started to leak. This is why they give you the gasket. The new latch does not always match to the same seal o the gasket. Replaced the gasket took less them two min. Ran the dishwasher again no leaks and the handle you can use one finger to unlock.

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

Simple repair.

New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Manually took off melted parts and replaced them with the new ones.

My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.

After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.