Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator light wouldn't come on.
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
All the repair people was on the money . I read them all .1--- NO paper work with new valve (.no instructions) ..2--- bracket is not the same .. I reversed my braket and it worked fine .you do not have to bend bracket.3--- It will take a day or so to start making ice..4--- the plastic nut is no longer needed on the new type outlet valve ....5--- the new outlet valve looks a little different from the old valve. WORKS GREAT ..
I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver under there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.
Left Vegetable Drawer Slide Rail was broken thus making it impossible for the Crisper Drawers to function properly.
I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
I took the ice maker tray out and dumped the ice and then removed 4 screws to take the plastic front off the drawer. I then took 4 more screws out to remove auger assembly. I could now unscrew the broken nut and replace it with the new one and put the snap ring and washer back in place and then put everything back together. Done Had I had my lathe running at the time I would have made this part out of aluminum instead of the new one and original that is out of plastic which is why it did not last.
Bracket was broken near the front mounting location causing the rt drawer
First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Ice maker would only make very small and very few ice cubes.
After determining that the ice maker on this relatively new refrigerator would make ice cubes if it received the proper amount of water. Ordered the valve and received in a couple days. Using a nut driver, removed the cardboard cover from the back of the refrigerator. Removed one screw holding the valve bracket to the fridge and removed another screw holding the water supply line and the water line to the ice maker in place. Pulled plug on fridge and removed 2 wires from valve. Removed inlet and outlet lines from old valve and reversed the process installing the new valve.