SVE47600B Jenn-Air Range - Instructions

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

Followed video

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

Followed provided video

1. I removed the 4 Philip head screws that hold the trim plate on the bottom of the display panel and also removed the knobs from the display panel. 2. Then I removed the 4 hex screws from the bottom of the front panel 3. Remove the display panel and expose the Electronic clock. 4. Remove the two hex screws hold the clock. Moved the clock, then remove the three connections to the clock. 5 Attach the connections to the new clock and reassemble everything in reverse. Take about 20-30 minutes. Not a difficult job.

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

I never reply to these surveys, but this was so brain dead simple, I had to respond. You take off two safety screws ( the ones that keep the oven door from falling off) You take off 6 screws holding the door together in order to remove the old hinges, put in the new hinges, put the six screws back in that hold the door together, put the oven door back on. Oh, and then put the two safety screws back in the so the oven door does not fall off. The only advice I have is put a big beach towel down to keep anything from getting scratched. Very Easy and saved me a lot of money.

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

STEP 1 GO TO YOUR ELECTRICAL PANEL AND SHUT OFF THE BREAKER OR REMOVE THE FUSE. A drill/driver with a phillips bit and extension is all you need. The 1/4" extension is the correct size for the hex screws. Remove them, then the phillips screws and put aside. Remove the control knobs, then the small screws behind them. Remove the trim and clean as it is most likely somewhat greasey, pull the clock board away from the range so that you can disconnect the wires. Lift the tabs holding the ribbon cable to the board and remove the cable. Now that wasn't as hard as you thought it would be was it? Now reverse the proceedure and you will have a working stove again and will have saved a $100 service call. Don't forget to reset the breaker.

Lifted the old one out and put the new one in. Very easy

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

Slowly disassemled door from outside in. This included removing the section below the door to access the screws that were inserted vertically into the bottom of the door. There are hex screws and phillips head. There were several pieces of glass in the door that had to be removed to get to the inner glass. We finally lifted out a frame that held the broken piece and one other. Working on a flat surface we unlatched a small tab in one corner (pliers) and unwrapped frame just enough to release broken sheet. Wearing gloves we removed all the broken glass and gently inserted new piece. Realigning the other piece of glass we gently closed the frame reinserting the tab of metal and securing. Would HAVE to have two people to do this! We then reassembled the door reversing the process. Note: It is a SMALL hex screw.