Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SVD48600W Maytag > Instructions

SVD48600W Jenn-Air Range - Instructions

All installation instructions for SVD48600W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SVD48600W
271-285 of 346
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

very old grease filter.

  • Customer: Eliane from Potomac Falls, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.

Simply replace the grease filter

  • Customer: MaryAnn from Scituate, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Thanks for carrying this part for my old stove. And thanks for the great service.

temperature varied in oven.couldn't set

  • Customer: tom from winter haven, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

Oven Would Not Start and F1 error code.

  • Customer: Michael from Fuquay Varina, NC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1.)Unplug the oven from power. 2)remove two screwd securing sensor inside rear of oven. 3)pull oven away from wall/cabinet enough to access rear of the oven. 4) unplug sensor wire harness, and remove sensor from inside of oven. 5) Pass wiring harness of new sensor through inside rear of oven and secure with screws remove from original sensor. 6) connect wiring harnes at rear of oven (PartSelect sends two harness adaptors - sweeeet). Done = BONUS - you get to clean the floor under the oven. To replace the Bake/Broil/Convection Relay Board, remove the cover from the rear of the oven by removing the four sheetmetal screws- 1) Create a diagram of the relay board and depict the wiring colors connecting to the existing relay board (THIS IS A "MUST DO" TASK). 2) remove wiring from existing relay board by pulling connectors from the relay board. 3) Remove the relay board (there is wiring that may need to arranged to remove the board) 4) Mount new relay board. 5) Using the diagram created in step 1, connect the wiring to the new board 6) Attach cover on back of oven using care not to pinch wiring. 7) Push oven back into place. 8) Reconncet oven to power. DONE.

Top oven sensor

  • Customer: Alan from Bonita, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

oven light replacement

  • Customer: martin from portland, OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

Long Oven Sensor failure - oven over heated & shut down

  • Customer: JAMES from SEATTLE, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

No Lights on Display

  • Customer: Mary Ruth from Cleburne, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did the repair on my Oven.He pulled the oven out of cabinet about four inches.He removed the front display panel held by 7 screws.Two screws removed to release Clock control board.Three cables were unplugged.Install new Clock control board.Plug in three cables.Install front panel.Push oven back into cabinet.Total time fifteen minutes.Clock worked great.

oven not staying on. fault cod F-3 showing

  • Customer: James from Cumberland, MD
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

Element in oven would not adjust to the oven temperature.

  • Customer: Dolores from Edmond, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

Oven would not turn on and get hot.

  • Customer: Tom from Altus, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

clock/display panel faded out to black over time

  • Customer: Claudia S from Los Ojos, NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair went just as the directions that came with my order confirmation stated. It could not have been more straight forward. I love my new bright clock and panel display! Thank you PartSelect.

Filter element missing screen material from age and cleaning

  • Customer: Harry from Bedford, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Lifter grill and replaced filter. It fit perfectly.

Oven randomly turned off and locked

  • Customer: Robert from homilton, MT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replace the oven sensor per the excelent easy video you provided

F-4 Code, oven wouldn't heat

  • Customer: Gary from San Jose, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.
All Instructions for the SVD48600W
271-285 of 346