Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The seal in the door was broken.
I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.
I removed two screws that hold unit to countertop, just pulled out unit about two inches. Removed broken door springs. Installed new door springs and pushed unit back into place and installed the 2 countertop screws DONE.
used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.
Removed the "kick plate" (4) screws. the hard part was attaching the springs to the door hooks. you cannot see them, have to go by feel. then stretch them to lower frame. attached the lower door trim piece with three screws.
I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!
Door sagging when open & sever water leak from door.
The parts arrived 20 hours after ordering -great service & the parts were just like like the removed parts only new. The old door gasket was pulled from its groove & and the new gasket was installed witout using tools. No more leaking water.The door spring installation wesa bit more difficult. The front bottom was removed with a nut drive, the broken springs were fished out, new springs were pull onto the arms and the cover put back in place. Not a bad job for a crippled, one-eyed 82 year old man.
My Diswasher was leaking from around the door gasket.
I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work with. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.
dishwasher was leaking at heating element connections
Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.
First I checked the water solenoid with a multimeter. Then traced the problem to the timer. I removed the screws that held the panel and timer onto the door. I replaced the timer and panel. It was a lot cheaper than buying a new dishwasher.
Ordered the new roller assembly and in no time the upper rack was back together, up and running. Now to see about replacing the other two rollers and the side rails as they are showing wear and tear.
Removed lower panel; unmounted fill valve assembly. Installed two springs. Remounted fill valve assembly and reinstaslled the lower panel. Door must be in a near closed position to gain access to the door "L" spring brackets.
Got the parts in a DAY! Wheels were broken and worn causing top tray to slip off runners- new wheels were easy to put in-used the screwsfrom the old ones and banged out the job in about 20 minutes, including letting my son help. Thanks Partselect, you've hooked a new DIY'er (my son)