SGR341AS0 Westinghouse Dryer - Instructions

purchased bearing kit

Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

Just want to say what a great company to order parts from, I ordered the wrong parts by mistake, broke the part trying to install the incorrect part, emailed customer service and they not only gave me credit for the wrong part I ordered but, also for the shipping...I will definitely be ordering again from this company

Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.

Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

I remove the drum, and install the bearing just like the instructions in the video.

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

Pried the lid up and flipped it back then disconnected the front panel wiring harness and then popped the front panel loose at the top and dropped it down. Disconnected the ignition coils, removed the coil retainer bracket and replaced the coils. Reassembled it in reverse order, performed functional test. Success!

Before you can remove the drive motor from the dryer, you will also have to remove the fan shroud and fan. To remove the fan from the drive motor shaft will require a 13/16 six point socket with an extension. Grip the belt pulley on the back of the motor with a pair for pliers so it doesn't move. Put the socket and extension on the plastic nut on the fan and very carefully turn clockwise (this is a left handed thread so it is reversed from a normal thread). If you end up rounding off the nut (which I did) you will have to beat a smaller socket on the nut and try again.Needless to say I ended up purchasing a new shroud and fan, since they build the shroud with the fan inside it. My suggestion is to purchase a fan and shroud in advance just in case you cannot get the fan off without ruining it. You can always return it if yours comes off easily. I hope this helps, as I had to wait another week to get my shroud and fan assembly.

watched the video My dryer was a little different but it came apart easily and was an easy fix. My wife did it all by herself.

You tube has quite a few videos that walk you right through the entire process. Due to the age of my dryer I replaced the belt and the Rear Drum Bearing kit while I had it apart. There were videos for all of it. Easy fix.

The belt arrived in 2 days. I cleaned the inside and it took no time to replace the belt. All I did is removed the front.The video was very helpful.Your magnet is on my refrigerator for future orders. Thanks.....Andy

it was so easy using the video that you emailed me. I want to rebuild my whole drier now .