Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SF368LEPS0 > Instructions

SF368LEPS0 Whirlpool Range - Instructions

All installation instructions for SF368LEPS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SF368LEPS0
76-90 of 186
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burned oven bulb

  • Customer: Ivanka from Atlantra, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 8 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

oven door sagged & wouldn't close properly

  • Customer: Jeff from Palm Beach Gardens, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 23 people found this instruction helpful
Took off oven door removed all screws to get old hinges out. Replaced with new hinges and put the door back together.

oven light burnt out

  • Customer: William from Schwenksville, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

the screws fell out of sides and bottom of door,bottom frame was bowed out.

  • Customer: Christine from Clinton Twp., MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
I had to get someone to help he thought we ordered wrong parts. called part select and was told to call whirpool direct. found out the part was redesigned unkown to us. So we were trying to fit parts that didn't need screws and now I have extra screws that I will send back.

light bulb went out in my oven

  • Customer: Janet from Ada, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Glass Door Broken

  • Customer: Myron from Punta Gorda, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 7 people found this instruction helpful
Removed 3 screws holding the glass door bracket.
Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.

door glide broken

  • Customer: David from Port Orange, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed the old ones.then installed the new ones.

slides on lower drawer were broken

  • Customer: Leona R from Louisville, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Inside Light would not work

  • Customer: Dan from Caddo Mills, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 5 people found this instruction helpful
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Worn/Bulb Socket

  • Customer: JOSEPH from COON RAPIDS, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

oven light not working

  • Customer: Richard from Gaylord, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 5 people found this instruction helpful
replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

Switch had burned out due to faulty wiring by electrician when appliance first installed

  • Customer: Doriss from Cartersville, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
my son simply replaced the switch, so now I have a working oven light once again

range handle fell off and screw got lost

  • Customer: Frances from palm beach gardens, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Followup Repair to Install Door Trim

  • Customer: John from Madison, WI
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragile plastic that had broken on both sides when I replaced one inner glass piece that had broken.

Damaged Socket When Removing Bulb Base

  • Customer: Charles from Oceanside, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
All Instructions for the SF368LEPS0
76-90 of 186