All Installation Instructions for Jenn-Air Range SEG196W

Malfunctioning Switch on Jenn Air D156W

Just wanted to thank you for the great service. I ordered the part on Tuesday, it shipped on Wednesday and arrived on Thursday. I installed the switch in under :10 minutes on Friday and the old Jenn Air grill is running like new again.
Many thanks!

Parts Used:

Toggle Switch - With Push Nuts

Mark from Coconut Grove, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The plastic holding the Switch for fan/light broke

A little difficult getting the old retaining washers off of the old part and placing the new washers on the new switch. I ended up using a nutdriver on the retaining nut and hitting it with a hammer. This worked great!! Make sure to record which wire color goes where on the old switch before removing wires. TURN OFF POWER BEFORE!! This is 220V. It can hurt you bad.

Parts Used:

Toggle Switch - With Push Nuts

Roger from Lebanon, TN
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electronic Clock Assembly quit

It was easy to get apart. I drew out a schematic of where the wires were so I could put them back in the same place. I plugged them all back up and it worked! Only problem was, there was a dead mouse behind the panel! He had not chewed anything, so the unit just went out from age.

Parts Used:

ELECTRONIC CONTROL BOARD

Gayle from Lenoir City, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

switch broke off and fell into oven cavity

removed two screws, pulled up hardware / components, unplugged the old switch, (remember to switch off the circuit breaker!) the two 'fasteners' that are supposed to keep the switch tied to the cover panel did not fit, so i had to use epoxy to secure the switch. no problem though.

Parts Used:

Grease Filter

Toggle Switch - With Push Nuts

alfio from piedmont, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The oven door seal was frayed, due to using oven cleaner.

First I removed 7 screws, using a Philips head screwdriver, to allow access to the inside of the oven door. I then removed several more screws to separate the panel holding the seal so that I could remove it and replace it with the new seal. Once the seal was in place I re-inserted all the screws to the panel and door to complete the repair. The knobs just slipped on to replace the ones that broke and fell off.

Parts Used:

Oven Door Seal

Clock Knob - black

Robert from Decatur, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

needed new grease filter

Removed old grease filter,replaced with new grease filter. No tools needed.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.

Parts Used:

Grease Filter

Mary from Anna Maria, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners would not light sometimes

Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit

Parts Used:

Surface Burners Spark Module Kit

Robert from St. Remy, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

it was painless

just as stated before. Remove old burners from plate and reattach new burners.

Parts Used:

Front Burner Assembly - Black (Glossy Finish)

Rear Burner

judy from clifton park, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

needed new grease filter

It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)

Parts Used:

Grease Filter

Barbara from Hubert, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Filter Worn Out

Remove cover and install

Parts Used:

Grease Filter

Thomas from Berlin, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Had to replace grease filter

Nice filter. Exact fit. Had a little ring to use to pull out to clean. Shipment was packed well.

Parts Used:

Grease Filter

Donald from Cottage Grove, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

50 year old oven racks in bad shape

Parts no longer available so we went to several appliance stores and measured racks. We found a jenair model had racks that measured correctly got the model number and ordered the racks. There working great and now the oven looks like new. Our kitchen is a restored 1956 GE metal kitchen in Cadilac pink. Thanks guys for the fast service and very resonsble price. Was also very happy to find the racks were made in USA.

Parts Used: