SEC350XX1 Roper Range - Instructions

Kevin from SPENCER, NE
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I snapped a bolt on the main power terminal block when connecting the pigtail.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Parts Used:

Main Power Terminal Block

Frank from Palm Coast, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wire came loose and shorted out

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Parts Used:

Main Power Terminal Block

Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My drip bowls were scorched and discolored and difficult to clean

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Parts Used:

Claudia from Milwaukee, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burnt out drip pans

I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

Parts Used:

Barbara from KAMUELA, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace burner drip pan

Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Parts Used:

Ray from Council Bluffrs, IA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Eroding burner drip bowls

Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement

Parts Used:

Edward from Hamilton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

reflecter/drip pans wrong size

Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.

Parts Used:

Dann from Glendale, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light burnt out

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Parts Used:

William from Schwenksville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used:

Ivanka from Atlantra, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Block broke

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Parts Used:

Main Power Terminal Block

Edward from Crimora, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ugly looking drip bowl.

Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

Parts Used:

Irina from Green Cove Springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replacement of drip bowll

take the old one out, but the new one in.

Parts Used:

Gudrun from Santa Fe, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bulb went out in my oven

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Parts Used:

Janet from Ada, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the drip bowls had rusted through

a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.

Parts Used: