S121 Jenn-Air Range - Instructions

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

I removed about 8 screws to disassemble the door to get the gasket in. This was an easy task. On the first use of the oven, it shattered one pane of the double glass door window. I think I installed it backwards since one pane is tempered glass, I believe. I installed the new window and am heating it up now - hope it doesn't break.

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

Replace filter

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

First, cut power to the range at the breaker box. I removed the jenn aire vent grill; removed two phillips head screws holding the switch bracket assembly and removed the switch assembly. After making a diagram of wiring, removed 4 bayonet type connectors. Next carefully remove the pushon nuts and save. Remove defective switch and discard. Install new switch on the two metal prongs over the black metal bracket making sure to orient correctly - use wire diagram and compare size of bayonet lugs for proper orientation. Push on nuts. Reconnect four wire bayonets; place switch assembly in proper position. insert and tighten the two phillips head screws that hold the assembly in place; replace vent grill and turn on power at breaker box.

Only problem was that new pushon nuts were too small for the jennaire metal prongs. Good thing i saved the old nuts!!

Installing the new switch was EASY. However, removing the old switch was very difficult due to the nuts holding the switch in place being designed as clamps not threaded screws and nuts.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The job was easier than I thought it would be. Turned off power at breaker first! Used phillips screwdriver to remove 2 fairly tight screws located on the vent side of the switch mounting plate. Flipped over plate and wrote down the 4 spade tip wire colors and location on switch. Removed the wires from the switch and removed the switch by prying off the locking washer with a sharpened/filed thin putty knife to get under it and then a flat blade screwdriver to finish removing it. Put the new switch in, hooked up the spade tip wires, mounted the plate back on and turned on the power. Worked great and I even impressed my Wife!