Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1435BK01 > Instructions

RVM1435BK01 Hotpoint Microwave - Instructions

All installation instructions for RVM1435BK01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1435BK01
76-90 of 214
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave will not start

  • Customer: Carlos from GLENDALE, NY
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.

Bulb broke in socket, socket had deteriorated beyond repair.

  • Customer: Frank from CICERO, IL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Both under mount lights were burned out

  • Customer: Divina from Grand Rapids, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed bottom panel, then unscrewed light socket, then replaced with new socket and bulb. Reattached socket and panel.

Remove old light sockets and replace in Microwave over stove

  • Customer: Cathy from LINCOLN, CA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.

bulb burned out light that is under the microwave, which lights the oven below.

  • Customer: Gary from UNIVERSITY PA, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

Left light inoperable

  • Customer: Paul from TULSA, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Ordered and received two parts. Price was exceedingly high. $13.34 for a simple light socket and $7.05 for a 40W light bulb. The ;light bulb was received with a broken filament so was useless. Went to a local bulb show and bought a new bulb at a fourth of the cost of the Part Select website. As fpr installation, to reach the old bulb, had to take off the bottom of the microwave. Replaced the socket with the new one and put in the new bulb. Everything OK now.

appliance stopped working -- no readout on screen

  • Customer: Carolyn from ARMONK, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
1. turned off electricity -- unplugged the unit 2. removed 3 screws on top of top vent, removed vent screen then I located the little white cylindrical fuse and popped it out with a table knife. Then I popped in the new fuse. Replaced the vent screen and screws -- plugged in the appliance and it is working again.

Bulb broke in light socket

  • Customer: Douglas from Ludington, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.

Burned out bulb

  • Customer: John from Waterford, WI
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 1 of 2 people found this instruction helpful
Screwed in new bulb.

Light bulb wouldn't light.

  • Customer: Steven from Marina Del Rey, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.

light lens broke a couple of years ago

  • Customer: KAREN from MANSFIELD, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.

  • Customer: Leon F. from Brookline, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.

Broken light lense

  • Customer: George from Marana, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed one screw, installed new lense in lense frame, rescrewed. Done.

bulb burned out -cracked holder lamp

  • Customer: Terry from Justice, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
pluged wires back on ,placed lamp holder and bulb back and replaced screws

Glass Carousel Cooking Tray Broke

  • Customer: Gary from Fernandina Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I received the tray and place it in the microwave for a perfect fit. My wife is so happy.
All Instructions for the RVM1435BK01
76-90 of 214