Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1435BD002 > Instructions

RVM1435BD002 Hotpoint Microwave - Instructions

All installation instructions for RVM1435BD002 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1435BD002
76-90 of 528
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bulb burned ot

  • Customer: John from Fort Smith, AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base

grinding of microwave turntable

  • Customer: William from Spring Hill, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

Microwave made squealing noise when on. Fan was worn out.

  • Customer: Richard from PORTER RANCH, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
This particular microwave is the over the range type, with an exhaust fan at the top and charcoal filters over the stove. Then to the side is the control panel for the microwave oven. You have to get into this to get to the fan. To do this, you have to take off the vent trim at the top of the microwave. Two screws. Open the front door and gently wiggle once the screws are out. Care must be taken with this because over time the channels that the screws go in can break, and then once that happens there's nothing to hold the vent into the oven. (I've replaced this once when both screw openings simply crumbled). Once it's off, there is a screw under it at the top of the control panel that needs to come out. There's another screw at the bottom of the control panel. Then, you slide the panel up about a half inch and then you can pull it out. After that, you can see the fan in there. There are two screws holding it in and a bunch of wires all around it. Pull out the multipin connector on the fan. There is a second plug-in wire that you may need to use pliers to get a grip on it. Pulling out a couple other nearby wire connectors will help loosen it all up so that you can move the wiring harness out of the way and tilt the fan out and remove it. Looking at the old fan, the bearings were tight and worn out, and that was the problem. It's not a particularly well made fan. Very simple open-frame motor with moving parts exposed, so it probably through the years ingested oil vapor from cooking, etc. Tilt the new fan into position, put the two screws back in and re-insert the wire connectors. Then all you need to do once all the wiring is neatly dressed again is put the panel back on, the two screws top and bottom, and lastly reinstalling the long vent at the top, (two long screws). Do that, and you're done. The microwave sounds fine now and works great.

Turntable quit turning

  • Customer: Tommy from West Chester, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I removed the broken turntable coupling and popped on the new one. Simple as that. It was a 2-minute job.

microwave dead

  • Customer: Jerry from Lillian, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 15 people found this instruction helpful
First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.

microwave would not start

  • Customer: JULIA from JACKSONVILLE, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
took of cover removed switch and replaced with new one

Glass Carousel Cooking Tray Broke

  • Customer: selwyn from inglewood, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.

Glass carousel cooking tray shattered

  • Customer: Susan from Marco Island, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
It took less then 10 minutes to order. Received new part with 3 days

Microwave would turn on when door opened

  • Customer: Lois from El Segundo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Left light socket was damaged beyond repair

  • Customer: Kathleen from Streamwood, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Roller guide for microwave turntable broke and could not be used.

  • Customer: Enid from Double Springs, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 11 people found this instruction helpful
Simply ordered a replacement part that was quickly and coveniently mailed to my home.

Glass turntable drive motor failure

  • Customer: Brent from Sacramento, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

Power worked but would not cook

  • Customer: Jim from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Replace broken control panel frame

  • Customer: mikael from brooklyn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 11 people found this instruction helpful
Once I read more on Partselect about how others had removed adjacent parts, I found it extremely easy. I had previously thought I would have to remove the microwave from the cabinet prior to repair, but once I looked at Partselect's expoded view of the microwave, it all became clear and took me longer to clean up than the actual repair.

Microwave turntable wouldn't turn.

  • Customer: Mark from Helena, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Removed broken coupler hub and pushed new hub on shaft. Make sure to align the new hub correctly when pushing on to shaft. Repair took less than 1 minute.
All Instructions for the RVM1435BD002
76-90 of 528