Models > RT16VKXDN01 > Instructions

RT16VKXDN01 Roper Refrigerator - Instructions

All Instructions for the RT16VKXDN01
61 - 75 of 185
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Parts Used:
Refrigerator Door Switch
  • Thomas from Roseville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could not properly open the door wirhout the handle
I Clean the handle both top and bottom. I place the cap in place on the bottom of the handle and tap it in snug with a hammer. I then place the top of the handle back into it's original position and then I screwed the end cap in place at the bottom. EASY !!
Parts Used:
Handle End Cap Kit
  • Kenneth from Neptune, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Parts Used:
Refrigerator Door Switch
  • stu from richmond, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigeration Door Handle End Cap cracked
The repair was REALLY SIMPLE. I popped off the cap cover from the existing end cap, insert the door handle to the new end cap, screw on the new end cap with a Phillips screw driver, and then push the old cap cover back on. Took less than 10 minutes, if that.
Parts Used:
Handle End Cap Kit
  • Jon from Brea, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Parts Used:
Refrigerator Door Switch
  • anthony from HAVELOCK, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Refrigerator door retainer
This job was extremely easy, snap on.
Parts Used:
Door Shelf Retainer Bar End Cap
  • Leroy from IRVINGTON, AL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain clogging causing water to leak bottom of fridge
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Parts Used:
Bimetal Defrost Thermostat
  • Ted C from DSRT HOT SPGS, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Faulty light socket
Followed the video instructions.
Parts Used:
Light Socket Kit
  • Larry from HOUSTON, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper drawer rail broken at one end
The rail just snapped into place with a light pressure. I worried it would require manipulation or heavy pressure and I would break the end while installing it.
Parts Used:
Crisper Drawer Rail
  • MARTY from GREAT FALLS, MT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket wouldn’t hold door shut.
NO DIRECTIONS CAME WITH GASKET! Project failure as gasket tore on a corner. For the price of this gasket, I was DISAPPOINTED. Door is being held shut with a childproof strap.
Parts Used:
Fresh Food Door Gasket
  • Patti from GARNEILL, MT
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced cracked compartment door
removed old and installed new compartment door by hand.
Parts Used:
Compartment Door
  • john from NORWOOD, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door hinge broke.
Removed door and replaced bushing bracket was ok.
Parts Used:
Hinge Bracket
  • Bernard from DONALDSONVLLE, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator light would not turn on.
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Parts Used:
Light Socket Kit
  • Suzanne from STERLING HTS, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drawer cracked/split
I just slipped the new drawer into place. So easy, even a woman can do it! ( I am female!)
Parts Used:
Refrigerator Crisper Drawer
  • Yvonne from Fredericksburg, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
latch end of track broke when too full jammed drawer was forced
PartsSelect diagrams at their website made it easy to find and order the right part at a reasonable price. I removed the lower glass shelf and frame that supports it. I removed broken track and slipped in the new track and snapped it in place with the orifice at the rear of the track over small peg in the back of the frame. If I had called a regular refrigerator repair man, i'll bet this job would have cost me at least 70 or 80 dollars,
Parts Used:
Crisper Drawer Rail
  • H. James from Bella Vista, AR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RT16VKXDN01
61 - 75 of 185
Back to Top