Models > RND24EY-3A > Instructions

RND24EY-3A (5M69B) Amana Refrigerator - Instructions

All Instructions for the RND24EY-3A
121 - 135 of 137
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator not cooling
Unloading the freezer and removing the back panel were the most time consuming aspect of this repair. Many models only have 4 screws, but this one has 9, and being a side by side it was a tight fit to reach them. Once defrosted we tested the thermostat, found it "dead", and ordered a new one. The part came within 3 business days. Installing it took minutes, since we had not permanently screwed in the back panel again. We didn't want to reload everything until we knew things worked properly, so we didn't put everything back right away. We thought we had further problems as the freezer got really cold but the frig still didn't get down to temp. Turns out we just needed to reinstall the fan shield which we'd taken off along with other parts to access and check the vents. The fan shield must be in place to direct the cold air into the vent to the refrigerator. Duh! It was an oversight that once caught made total sense! Now all works fine on this 20 year old Maytag side by side!
Parts Used:
Defrost Thermostat
  • John from Niles, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice bin drive ring was cracked
removed torx screws and replaced ice bin drive ring.
Parts Used:
Ice Bin Drive Ring
  • Jesus from Santa Maria, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Condensor Fan going bad
I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!
Parts Used:
Condenser Fan Motor Kit
  • George from Hickory, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The freezer compartment was not cold enough.
I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!
Parts Used:
Condenser Fan Motor Kit
  • Tom from Paducah, KY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Condensor motor was frozen
pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.
Parts Used:
Condenser Fan Motor Kit
  • john from thibodaux, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Parts Used:
Light Bulb - 40W
  • Grant from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
compressor will not start - when you turn it on - it hums for a few seconds and them you hear a click sound (the overload opens) and the hum stops
be sure the power cable is NOT plugged into an electrical outlet - removed the cover on the bottom rear of the refrigerator - using a flat blade screw driver pry the cover off the side of the compressor - remove the old relay - remove the wires from the old relay and install them on the new relay in the same location - install the new relay on the compressor connections - snap the cover back on the compressor - replace the cover - power the refrigerator on - the compressor should start and run normally
Parts Used:
Refrigerator Compressor Start Relay
  • Cliff from Metairie, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Bin Drive Ring replacement
Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.
Parts Used:
Ice Bin Drive Ring
  • George from Pleasaton, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light socket not working
Pull out plastic cover #13of refrigerator part discription (temp. control and light socket), snap out old light socket and replaced with new light socket. light is now working.
Parts Used:
Light Socket
  • Romeo from Edinburg, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
refridgerator was not cooling to the proper temps and finally would not cool at all
Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.
Parts Used:
Condenser Fan Motor Kit
  • John from LAS CRUCES, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Ice Maker Motor From Plastic Ice Tray
Given that the augur motor had broken away from the ice tray, removal of the ice tray was simple. Simply remove one screw and slide the tray up and out. Removal of the motor was simple by squeezing the top and bottom of the wire harness plug located on the back of the freezer compartment wall, although it was by feel. The real problem came with trying to remove the augur from the motor shaft (it has a left hand tread) it is on tight and while trying to remove it – I stripped the threads on the motor shaft and couldn’t get the augur off. That’s when the cussing started. No easy fix for this so in addition to the ice tray, I had to order a new ice bucket auger drive motor kit (which included the augur for the end of the motor shaft). Once all the parts arrived, and I had the motor and solenoid assembled and mounted to the back of the tray, the hardest part was plugging the motor back into the plug on the back of the freezer wall- you’ll be doing this by feel (which is a poor design). One suggestion, take a picture of the wire connections between the motor and solenoid – just to be on the safe side – before taking it all apart.
Parts Used:
Ice Bucket Auger Drive Motor Kit
  • Jim from Washington, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken ice bin drive ring
Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.
Parts Used:
Ice Bin Drive Ring
  • James from Lincoln, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Fan motor worn out
My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's working fine now and I'm a satisfied customer!
Parts Used:
Condenser Fan Motor Kit
  • Myrna from Decatur, IL
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
Was this instruction helpful to you?
Thank you for voting!
condenser motor broke
opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.
Parts Used:
Condenser Fan Motor Kit
  • patrick from livonia, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
wouldn't make ice, door seal was hot to touch, warm in fridge.
I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.
Parts Used:
Condenser Fan Motor Kit
  • Dale from Sterling, AK
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RND24EY-3A
121 - 135 of 137