REX4634KQ1 Roper Dryer - Instructions

I viewed a number of vidieos on the Webb to determine the possible problems. The vidieos explained and demonstrated how to test the parts that could have been causing the problems. I tested the parts described in the vidieos and the ones I was able to test showed that they were not defective. I was unable to test the Cycling Thermostat and the High Limit Thermostat to my satisfaction so I ordered the two parts and installed them as demonstrated on the vidieos. The dryer works as if it was a new one. I am a very satisfied customer and will definitely purchase my parts from partselect.com in the future.

Took off the back panel removed old wires. Piggybacked new wire and put back together. The video was very helpful as far as where exactly to insert the new wire. Overall a very good experience. When it first happened my husband and I thought we would need a new dryer. We found your website and figured out what the problem most likely was. Ordeed the part it came within a few days. The money we saved not having to get a new dryer is great.

After removing the bottom front panel using a putty knife to pry the upper left and right edges of the panel, I noticed that the long thin drum belt had broken. I went online to PartSelect, and using the Whirlpool model number, found the parts diagrams. Since the dryer is 20 years old, I decided to order the maintenance kit part# PS373087 which includes new idler wheels, retainer clips, and a tension pulley as well as the belt . I found a number of webpages that offer guidance in replacing the belt. Along with the instructions that came with the maintenance kit, I was able to do the repairs and have the dryer up and running in 30 minutes. Remember to remove the door springs before taking off the upper front panel. You only need to loosen the bottom screws on this panel. Leaving them in place helps to align and hold the panel when re-installing it.

Dryer started to turn but stopped putting out heat. I used a multimeter, and found both high limit switches to be good, and all other electrical components good. I removed the heating element and examined it to notice that the first coil was broken. I ordered the new part and replaced it, and all is well, better than before.

I watched a youtube video about how to replace a dryer belt. I did what it said.

Followed the On Line Repair on my Lap Top. Very Easy !

Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.

Watched installation video (very hepfull),used battery driver (faster)to remove back (9 screws). Used nutdriver to remove screw holding old part, removed part. Changer wires one at a time to prevent wrong placement of wire. Parts ordered were correct and arrived in 2-3 days. Thanks PartSelect. Very easy install, video made me an "instant repairman."

The first thing I did was unplug dryer from outlet. Watched installation video (very hepfull), the back was removed and dryer unpluged because I had replaced Thermal Cut-Off Kit, High Limit Thermostst and Cycling Thermostst ordered two days earlier. Forgetful as I am I did not check Heating Element with ohm meater, It was bad, ordered new one. It arrived as promised and was correct part. Removed two screws holding heating element in place. Removed four wires one at a time, placing them in correct place on new element. Replaced element and two screws. Job complete. Pluged it in and dryer is working like a new one.

Thanks to your video my husband felt very confident and the belt was installed with no problems.

After doing on line research at other sites, I bought an inexpensive multimeter, took off the back of the dryer, and started trying to figure out what part wasn't working. I might as well have tried to diagnose a jet engine problem, I didn't have a clue. Then I went to the Part Select site, and their stats showed that in 50% or so of the cases where a Roper doesn't start, you need a thermal fuse, and should also replace the cycling thermostat while you're at it. The "how-to" video showed me exactly what the parts look like, and where they are in the machine, and the cost of the parts plus delivery was less than $50!! It was worth taking the chance for $50. The parts came in two days, were installed in five minutes, the dryer works and I'm thrilled! Part Select is the absolute best. This is the first appliance repair I've ever done. I would never have done it without you. Thank you.

Watched the video on your site. Removed the nine screws, snapped in the element and replaced the screws. The video is perfect.

ordered new latch. Arrived promptly. Installed in 5 minutes. Actually easied than the video. Thanks

The Door Catch Kit had clear instructions for installation and included multiple replacement catches to fit several different sizes/varieties of dryers. I used a screwdriver to pry out the broken door catch, popped in the replacement, and was done! As usual, PartSelect had what I needed at a good price, with clear instructions for any needed installation. Fast shipping, too.

Computer said only two things were probably wrong, heating unit or fuse. My son unpluged the unit, opened the back looked around and saw the burned, broken wire in the heating unit. Orderd part, deliverd in a few days (Issac inteferred) put in the new heating unit, replaced the back, closed the unit, plugged the dryer into the eltricity, pressed the start button and there was heat. Very easy repair and a lot more reasonable then calling a service man.