REX3514RQ1 Roper Dryer - Instructions

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

Just as your helpfull diagram of the dryer said, removed the rear panel,there it was, i recongnised it by the part you sent, pull it out of it's position, had a little truble figuring out the piece that fits on where the electric prongs are, after looking found out the piece was held on with a clip that goes inside the housing, Haaa. the rest was easy. Thanks,It works great. Dick

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

I followed the repair method as described in the how to video it was as easy as that. Dryer is now working perfectly

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

Just as in the video. Sounds like new. Had to feel it to make sure it was running.

removed access panel installed new switch reinstalled access panel

Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

Replaced Broken Belt and roller

Replaced the Drum Roller, Belt, Belt Tensioner and Rear Drum Seal by watching the video that was attached with the order form from PartSelect. Removed screws from lint filter, raised the top by sliding it forward a small amount, able to raise top and leaned it against a wall. Then removed two screws from front panel and lifted front up slightly while holding the drum and removed it from front of dryer and placed it out of the way. Loosened the tensioner pulley to remove the belt and once that was done pulled the drum out and replaced the drum rollers (by looking at the video). The rear drum seal was the most aggravating part in getting it off and cleaning it up. Was a little messy putting it back on and then just reversed everything to put it back together. It is working properly now. Thanks to the video. PartSelect parts came earlier than I expected they would and I appreciated that very much.

It took longest to take apart and test to see which part was bad. I had never done it before. Got it apart and used the drawings on Parts Select to find location of parts. Testing only few minutes found bad thermostat.Ordered parts, and they came in 1 1/2 days. I replaced both thermostats being they were in the kit. Actual repair took maybe 15 minutes. Vacuumed out everything I could. Took lint trap out a vacuumed. Put it back together, plugged it in, heated like new. All time told I would say little over hour.

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

Replaced Thermal Fuse