Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven gasket was leaking
Old gasket had become brittle. Was able to find the 22 yr old model and part on PartSelect (could not track it down on GE's site. Inner panel was removed with four screws. Old gasket came out. Installed new gasket making sure the bead fit into the groove provided in the door panel. Re-assembled. All is well. Thanks
Downdraft stove is over 20 years old, but everything else works fine and it would be a real pain to replace it.
This quick-heat back burner is part of a two burner plug- in unit which takes up half of the top of the stove.
I removed the top from the rest of the unit easily removing five screws. Because of the age and long use it was tough getting the old nut off which holds on the disc, but with the help of some spray lubricant it came off. The old wire ends were also rusted, and to get them off I bent up the old holder, which was going to be discarded anyhow. It was a simple matter to plug in the new unit, tighten the nut, clean up the lubricant with a paper towel, and reassemble the unit, which I cleaned inside since it was dusty. After plugging in the unit I turned on the burner...it works like new and has saved me a very costly replacement. I like it so much that even though the front element works perfectly I am considering buying that disc too just so they will match. Finding your company was absolutely great, and I would recommend you to anyone looking for parts. I still have the manual for this stove so I would feel confident in replacing pretty much any part needed....not bad for a 72 year old woman, (My Dad taught me to do my own work and I am a passable carpenter and plumber; a little more wary when it's something electrical !
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.
Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the small wire nuts provided, then enlarged the hole in the oven wall, being careful not to pinch the wires then pushed the wire nuts and extra wire back through the hole and put the screws back in the flange.
After TRYING for 2 years to locate a bake element for this Range that has no model number we called your company and with the element measurements and you were able to cross reference and find us the right part. BONUS! We have an oven once again.
The element was easy to install, it did however take some bending to get it to lay flat.
You have a customer for life, I'll NEVER lose this website address.
This burner element is the large element of a 2 element modual. After removing the modual, there was 6 small metal screws to open the modual to expose the burner elements. After the burner element were exposed there are 2 wires that had to be disconected with a screw driver. Once the wires are disconnecter the burner element is easy removed by sliding the old element out and sliding the new element in. Just reconect the wires to the new element and put the cover back on with the 6 metal screws. It took about 30 minutes to complete the task, taking time to clean all the insides to bring it back to new condition. Very very easy job.
Disconnect power to burner module. Dissassemble module with nut driver. Screws connecting feed wires to burner were too corroded to remove. Cut wire close to screws, stripped insulation and inserted new ends into new burner. Reassembled module with nut drivers.
When moving the range, the 220 wire popped off the terminal and arced melting the plastic terminal
I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.
Piece of cake- remove two screws, remove old element, install new one. Shipping was prompt and I was glad to see the part was the genuine GE article. The price was also good- about a 40% savings over the local Appliance Depot!
I really just want to say how fast Part Select sent my part out...I had no idea it would arrive so quick...Thanks Very much for great customer service...obviously the installation of the bake element is very quick, all you need is a screwdriver, 4 screws, very simple..
We are really excited to have this burner working again. We originally paid a repairman to come out and he said that he couldn't get parts so we would just have to live with it or replace the whole cooktop. We received the new burner within a few days of ordering. I pulled the two burner unit out of the cooktop, easily removed about 7 nuts and had access to the burners. It was a perfect replacement and fit right in. The only place I had to spend a little extra time was where the connection wires are screwed to the burner. One unscrewed but the other one broke and I had to cut it off the old unit and remove a little wire insulation before re-installing.