RB171TFV Magic Chef Refrigerator - Instructions

Removed motor in freezer replaced it with new motor

The replacement ice maker was exactly the same size and model. All the mounting screws lined up and install was snap. The website parts description was very good and helpful. We now have ice cubes with no over flowing glacier in the ice tray.

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

Followed the utube video demonstration. There was no instructions for changing the relay and overload and so this part was not used.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

Unlike what the online video showed, my bottom freezer French door refrigerator didn't use hooks to secure the icemaker in place. Instead, it used three tabs with screws to secure it in place. I could see two of them, but not the third one. After removing two screws and realizing that the icemaker was still pretty well secured, I felt around and found the third screw (at the top, right behind the front of the icemaker). Once I got that out, the replacement went easily, as shown on the video. That third screw was a little challenging to put back, but after a few tries I got it in. The icemaker is now making ice like a champ! Good work PartSelect! And the part came quickly, as advertised.

First pulled the Ice tray out of the freezer, Pulled the cord for the power to the refrig. Removed 3-Srews with the nut driver and disconnected the Power Supply to the Ice maker. Removed it from the freezer and started to remove the Bail and install the bail in the new Ice maker. Remove the cover from the side of the old ice maker and install it on the new ice maker. Put it back in the Refrig and connected the power cord and installed the 3-screws and reinstalled the Ice Tray and 30 mins. later it started making ice. Thanks for the Youtube Video it helped a lot to take the pressure off of doing it your self.

Unscrewed the right control knob. Removed the left temperature control knob (there is no screw holding it), removed one screw to rear of small panel then pried open from the rear of the small panel, there are two plastic tabs in front of the small panel holding it in place. Unscrewed the failed control unit and replaced it with the new one. Replaced the small panel and screw then the left side control knob, making sure of the alignment in the "off" position as the knob has to be pressured into a clamp arrangement on the cold control thermostat. Re-screwed the right knob into place, as well.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th