RB15KN-3S Magic Chef Refrigerator - Instructions

I unplugged the fridge. Then I removed the ice bucket. Then I removed the ice maker using a 3/4 socket to separate the connections and then used a small screwdriver to separate whatever connections were left. Then I installed the new ice maker and checked its level. Everything now works fine.

turned off freezer unplugged ice maker ,unscrewed 3 screws, removed ice maker,wiring harness and wire that goes up and down to control ice maker. installed all in reverse put back in and turned on waited and waited no ice ,theres a little control valve that let's the water in as well that was shot as well had to go get one at a local shop fairly interchangable just pull the other out and take with you,or just order one with your ice maker if you have the fridge out you might as well change it as it's just as old as the ice maker as well .everything pumping well,like never before, tons of ice all the time also put in filter on the water line as well really good tasteing ice now.

The old light fixture and socket were easily removed. This was done with the power connected, but I already knew the switch didn't need to be handled. The solderless connectors are all insulated, so I just had to be careful. The new socket would not accept the connector for the "hot" (red) wire in the fridge, due to a design change. This is, of course, why you furnished a loose 3/16 inch crimpon connector. Rather than cutting the red wire (remember, the power is still connected), I obtained an insulated 3/16 connector of the opposite gender, and a short piece of red-insulated wire from an old fluorescent tube ballast, and made a jumper. The connector I provided (male) did not fit tightly in the original fridge connector, so I put a layer of resin-core solder on my male connector. You need tight connections. If the solder layer is too thick, it's easy to file down. Make sure to heat the solder sufficiently that the solidified solder is shiny and not dull gray. I used a 100-watt gun. 20 watts would probably work too. DO NOT USE ACID-CORE SOLDER OR FLUX ON ELECTRICAL WORK! I knew the switch was good, because I had checked for voltage at the socket terminals using my voltmeter, before I ordered the socket. It read 120 volts every time the door switch was open, and zero volts every time the door switch was pushed closed. A simple voltage tester would work here, too. Be very careful if you do this test or this repair with the power connected to the fridge; there is considerable potential to find yourself touching 120 volts with one hand while your other hand is touching a perfect "ground". There doesn't seem to be any choice if you want to test the switch. You do have a choice with the socket replacement - - the jumper described above. If you're not going to use the jumper approach, cut the power! If you are going to make a jumper and are not comfortable working on a "live" circuit, cut the power.

The fix was relatively easy but I could not get 2 of the screws removed. They were in very tight and I didn't have the right tools. Also, in the Amana refridgerator, they are in a "difficult to get at" location. I called my plumber friend and he helped me. Once the screws were out, the rest of the job went very smoothly as others have described. We took out the bad icemaker and reconnected the new one to the existing harness. I had ice in an about an hour. Thanks so much, PartSelect. The delivery was quick and the install was as many described on your website. You provide a wonderful service for the "do it yourselfer". Terri

Disconnect ac power line, disconnect power line going to the water valve. Turn water off atthe cockvalve. Disconnect water line to valve. Disconnect plastic tubing going in the valve. If plastic is old you may have to replace it to keep from leaking at the quick connect coupling. Connect water line and plastic tubling to new valve, connect power clips to new valve. Plug in the refrigertor and turn on water at the cock valve and your good to go

First, watched video on Part Select Website. Very good. Pulled Appliance out from wall, Pulled the power plug, and removed the back shield covering the working parts of the unit. Found the fan and it was almost the same setup as on the video except that I could not get to one of the screws holding the motor in place so had to remove the entire bracket with the fan. Not too hard. Cleaned away dust and gunk around the site and noticed that the fan pulled air through a tunnel-like condenser coil that was packed with gunky lint...this is what probably killed the motor. I cleaned out the tunnel with the bottle brushes and vacuum and installed the new motor / bracket assembly. Then replaced the shielding around the fan and the back cover .panel. This is important because these form the channel that guides air flow throughout the condenser coils. This particular refrigerator has a barrier underneath which guides air flow from the front left to the condenser, through the fan, over the evaporator drip pan and out the right front. I cleaned all the lint and gunk from this area as well. I also made an air filter (cut from a furnace filter) and wedged it in front of the air entry section. This should keep the condenser coil cleaner over time but you have to remember to change the filter once a year. Probably should clean the condenser coil every 5 years as well. This unit has been very reliable over 20 years and may well go for another 20. Good luck with your repair.

Couldn't believe how complicated this part is with heaters. It is used in at least a billion refrigerators and functions well. But I had to tear it all apart to adopt it. Got it all done and stayed awake all night for waiting for Ice. Nothing! Then a Erika moment! Turn the ice arm full switch off! Then Ice poured out every hour. Expecting many years of ice. Thanks for speedy delivery especially before Christmas..

need instr. to repair

The repair was a lot easier than I thought. I first ordered the ice-maker part from PartSelect. Followed the instructions from the how-to video and I was done within 30 minutes. Unplugged the fridge, took out the two 1/4" nut screws holding up the ice-maker, disconnected the wiring harness and then re-attached the new ice-maker in reverse order. Had to use some of the parts from the old ice-maker, like the cover, ice wire (the wire that moves up and down, letting you know when the ice box was full or starts the ice-making process) The whole process along the PartSelect video made it easy.

Viewed the viedo - it showed what to do

Watch the video and then do the repair.

Unscrewed the right control knob. Removed the left temperature control knob (there is no screw holding it), removed one screw to rear of small panel then pried open from the rear of the small panel, there are two plastic tabs in front of the small panel holding it in place. Unscrewed the failed control unit and replaced it with the new one. Replaced the small panel and screw then the left side control knob, making sure of the alignment in the "off" position as the knob has to be pressured into a clamp arrangement on the cold control thermostat. Re-screwed the right knob into place, as well.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

The refrig. Is about 30 years old. The new solenoid looked and mounted nothing like the original. I driled holes in the frig and attach the solenoid with sheet metel screws. There were not enough fittings and hoses so I bought a braded metal hose to attach the ro line and the valve inlet. I used the parts in the kit to attach the water feed line. To the ice maker I did not try to stuff all the hoses and lines back into the cramped cavity in the frig. W ell how does it look? The solenoid sticks out a little and there are a lot of hoses behind the frig. I do not spend much time behind the frig so who cares. The ice maker is making ice!