PLD4375RFC3 Frigidaire Dishwasher - Instructions

Simply unscrewed the old part and screwed the new one on. No tools needed, all done by hand.

The replacement basket fit perfectly.

Unscrewed old upper arm assembly by hand and screwed new part on. The new part was a perfect fit and has worked, with no further problems.

It's as easy as everyone said. Only problem I had was that since the seal is now used on several models, I had to trim about an eighth of an inch off the left side to keep it from hitting the door seal. No more leaks and saved probably $100.00 plus on a repair visit. The seal probably wore out because of using to much Cascade!

I used a screwdriver to pry the Spray Arm Center snaps loose from the top drainer basket, and the same screwdriver to pry the Spray Arm Center into position. Job done..!!!!

Very fast shipping from parts select. Un-screwed part by hand and replaced with new piece. Easiest appliance repair ever. I would say anyone could do it. Great Experience with Patrs Select. Thanks.

I just hand-tightening the new sprayer arm in place. Very easy. Beacuse of new design, the arm looks like it will remain in place.

We had a leak around the bottom of the dishwasher door. After finding this site, I identified the part that I needed, the bottom gasket. I was ready to take all the screws out of the door to pull out the old gasket until I read the reviews and repair experiences here. Just have to grasp the old gasket with pliers to pull it out, straight down. I cleaned out the slot with a thin putty knife, just to make sure it didn't have any gunk left in it. Then simply slide the new gasket back in place. The only "trick" is to be careful lining up the slot on the right side, to make sure it seats all the way down. Like someone else already mentioned, there is no "click" to indicate it is all the way in, just a feeling of snugness. Closed it up and made a test run of the dishwasher, and, Voila! No more leak. A hell of a lot cheaper and faster than waiting for a repairman. Oh, I almost forgot to mention, I received my part within 24 hrs of ordering it too!

Unscrewed the broken upper spray arm part and replaced it with the new part. Took 10 seconds to do the entire exchange. Perfect fit - no problems. Up and running immediately!

In assessing problem we turned off power and water supply and removed Water Inlet Valve. (less than 10 min.) Looked up info on Parts Select with model number. Found the part I needed within moments. (EASY). While on site checked troubleshooter and decided with noise to replace Drain Pump. Ordered both parts. Fed Ex delivered to wrong address. Postal Carrier let us know package was at house on next block. We retrieved package and 20 minutes later dishwasher was running. No leaking and I can stand in the kitchen and have a conversation without the dishwasher growling us out. Thank you for making this an easy fix. Easy to follow removal and installation instructions. You guys are awesome.

Took cover off door, unbolted hinges from door assembly, rotated door assembly to access inside bottom of door...took out old splash guard and installed new one. Reverse order to reassmble unit. Tested...no leaks.

I removed the all the screws to get the door panel off. Then removed the control pad from the control board and reversed it all. Super easy. Crappy dishwasher, great service from PartSelect! They are like the Zappos for appliance repair

I am so glad you asked. lol I am on top of the world. I was about to
just buy a new one but being old, disabled and living off SS I had NO
money!! I dont do much on computer but just goggled. I found your
store and my answer was there. Your site is so good even I found what
I was needing. With your video I was able to do it myself. Oh by the
way I would have paid 65$ for them to look at it, and I assure you
they would not have let in cost me the 14$ I paid you for the part....
I LOVE YOU!!!! Now I need gaskets for my frig and chest freezer. Got
those video's?Llike my great grand kids say "YOU ROCK" lol

I started to disassemble the machine from the inside, and discovered that I should have started from the bottom...At least now I know how to get to all the parts...I had to remove a couple of parts to get to the problem. Because the replacement part was slightly different than the original, It took some rearranging to get the hoses and wires to connect(original was mounted at 45 degree angle, replacement at 90)

just insalled the new part by screwing it onto the dishwasher. it took about 10 seconds. I ordered the parts and they were delivered to my door in lest than 24 hours. I will be sure to order parts from your company again when needed.