PDF820SGJ0BB General Electric Dishwasher - Instructions

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

The dishwasher was not heating anymore. I suspected it was the float/flood switch, so I got that ordered. I went ahead and ordered the element also and I'm glad I did! Even though the element was good, when I tested it I loosened the nut holding the element in. When I retightened it there was NO WAY for me to get it watertight again and it kept dripping out the bottom. Mine was made in 2019, and the gaskets on the element that came with it were a terrible design - the metal flange on the element was about as big as the hole in the middle of the gasket so water just leaked between the gasket "donut" hole and the element with no way to seal. The element I bought for this repair just in case had a totally redesigned gasket that sealed right up and didn't have the same design issue. So beware, if you are fiddling with the element in your process, be sure the gasket will reseal - or just have an extra new element in case it is the old (bad) design.

The flood switch was easy to find (with dishwasher on its back) in a white housing under the black circular sump.

Getting the actual switch out of that housing took some doing. I ended up using 4 small kebab sticks - toothpicks might work better- all 4 tabs have to be pulled out at the same time.

So I ended up changing out both the element (which was good but started leaking) and the float switch.

IMPORTANT!!! Before you put the dishwasher back in, you probably need to reset the thermal cutoff (TCO) on the back of the dishwasher. Follow the wire up from the element and it is the first thing it goes to. There should be a small (3mm) black button that has popped out. Press that back in. With your repair (float switch or element) it should start heating again - at least mine did.

Simply twist on the new part/filter.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

Process of elimination and a visit to my local repair store told me it was wise to try the tub gasket, and according to partselect.com, it solved the problem a majority of the time. My local repair dealer agreed: Try it. They agreed because for them to replace a lower door gasket AND the $10 tub gasket... if they came out, the service call and parts would equal half the cost to replace the whole dishwasher. So I bought a tub gasket from partselect.com and replaced the old one. It worked, it was easy, so if your same make & model is leaking? Try it first. That's my advice.

Water valve replacement was easy. Turned off water supply valve. Unscrewed water supply from valve on dishwasher, removed 2 water hoses , that feed top and bottom sprayer’s And reinstalled everything opposite of removal. 5min job

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked