PDC3600BWX Maytag Dishwasher - Instructions

Removed the old gasket, without tools, and fit the new gasket into the space, making sure it was in the groove correctly all around, job done, works great. The ordering of the gasket on this site was easy and the shipping time was amazing, one day. Would use this company again, and recommend to anyone needing parts that wants to do repairs themself. I am sure saved a whole lot over hiring someone, and got the job done sooner also.

First I unplugged the dishwasher since I was working on the electrical. I just unscrewed all the screws on the inside of the door till I could get down to the door latch. I found that a tiny piece of plastic had broken off of the white bracket that holds the electrical switches (these turn it on when the door latches and off when the door opens). I had to break several tiny plastic prongs off the old bracket in order to pull the switches out of it (gently so the wires wouldn't pull out of the switches) and the door handle latch fell out easily. Then it was easy to snap the switches back into the new bracket, and slip the handle latch back in, and screw everything back down. It worked! I've never worked on a dishwasher before but looking at the photos of all the various parts (even the ones I didn't need to use) really helped me to see how the things go together and to narrow it down to which part I would need. The dishwasher was totally un-usable and all I spent to make it run again was less than $5. Thanks to Partselect!

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

1- turn power off. 2- remove 7 screws to take door apart 3- remove 2 screws to take dispenser out. 4- i unhooked electic plug from it. 5- replace grommet and all back together. not bad to be 72 years old.

I had to replace the faucet in the kitchen sink orignnally. However since I use a porteable dishwasher, its hose connects to the kitchen faucet. The new faucets aerator is threaded differently than the old so that the dishwasher adapter would not screw in. I had misplaced the adappter kit that came with the dishwasher last year, so I ordered the adapter from partselect.com. when the part came a few day it was a simple as screw out the old aerator, screwing in the new adapted and then putting the modified aerator from the old faucet back in so that the dishwasher can be connected as needed.

My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

Took the replacment rack out of the box and found that it was the proper one. Had to rotate out the water director tower from the orignal rack and install it in new rack which took a few seconds to figure out . it was time to discard the ailing rack! Apparently the dish soap can attack the rack materia if there is any metal exposed and rot it out like rust so when this happens time for a new one. Otherwise there are no pins to support the bowls and plates in the lower section.

Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.

I first removed the washer arm. Be careful because it is screwed on with the large center plastic piece with right hand thread. That allowed me to take the arm and disc off.

Next I took 6 screws loose with the allen wrench. This allowed me to get to the filter ring. I removed it and that allowed me to get to the three screws holding the discharge. I used a 5/16th socket to remove them.

A plastic disc that was part of the upper pump came loose and caused the noise. I replaced the upper discharge housing (with upper pump as part of it) and upper discharge housing gasket and reversed the order to reassemble.

The exploded diagram was a terrific help

Removed old door gasket and water deflectors and replaced with new. Got the gasket in backwards at first. Removed and rotated 180 degrees and it went in properly. (Used tech video provided by parts select to help me.)

Though the old gasket was definitely bad, water still leaked after replacement.

Key issue ...... over time, contamination has accumulated in the water shutoff lever assembly and also on the shutoff microswitch underneath the internal water float, making both sticky and non-responsive to water level. Water had been overfilling. (probably defaulting to a maximum number of seconds to fill). ALSO - original installation was not totally level, with back of tub higher than the front.

Leveled tub. Removed mocroswitch and lever and cleaned both of sticky grease.

No more leakage.. basic problem was actually overfilling, allowing water to surge into the lower internal door vent upon pump startup.

Ron
Mount Airy, MD

Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.

Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

I took the bottom rack out of the dishwasher. I then took the filter guard and bottom spray arm out. Then I took the screws out of the filter guard to get to the rinse arm. I took the filter guard off, took the old rinse arm out and put in the new one. Have to make sure it is completely resting inside there. Then I put the filter guard back on. Put the screws back into the filter guard, put the two arm seals down around the rinse arm, put the bottom arm spray with guard back into the notches, put the screw top on so it can screw back in and the dishwasher is ready to go. Just make sure that you don't have a lot of soap built up, it will not clean the dishes right nor will the spray arms move. I had to call my appliance person out, and I have so much built up from soap, that I had to order a new filter guard and top and bottom spray jets. I now know to switch back to powder or liquid soap, because the tablets make a huge built up of soap... I have these parts on order now. In the meantime, I am cleaning out the jets with dishwasher magic and vinegar while I am waiting for my new parts. I now know how to put things back together so when I have this happen again I will know how to do it to save me the 63.00 office call and parts. I am happy that I know where to get my parts when I need them or break them by accident on trying to put my dishwasher back together again. Thanks.

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

Front Door Panel was replaced by unscrewing 3 screws on each left and right side of the dishwasher.

The bottom screws did not need to be completely unscrewed, just losen it enough to be able to remove the panel out.

Replace it with the new panel and screw back in the screws.