Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door latch was broken
Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !
Removed the front panel,tiped up the top panel ,removed the drum, drive belt,motor and exaust tube assembly. cleaned and vaccumed all lint from every were. Removed motor from fan blade and houseing. Reinstalled moter and pulley that came with the moter and fan blade. reinstalled all of the rest of the parts and plugedin the wires. once all back together pluged into outlet and turned on and prasto works great.
my problem was easy, i orderd a new lint filter, for a dryer that is at least 10y/o. it came to me by FEDEX, in 3 days. i threw out the old one and put in the new one. easy peasy. i will say that this website had what i wanted and got it to me very quickly. good job by PARTSELECT......
Blower wheel shaft hole was rounded out, lamp was out
Removed two screws on dryer top and removed top, removed two screws holding front of cabinet and removed cabinet front to the side, disconnected wires to door switch, removed two bolts from motor mount bracket, pulled motor back to access blower wheel, removed old wheel and installed new one, reversed steps, unscrewed old light bulb and screwed in new one.
Had pure hell getting to drum belt and putting it back onto motor pulley and idler, cussed a little, didn't really help . replaced front of cabinet and top, did test run all worked ok.
This job was a little difficult, espicially accessing the belt and idler pulley...
The diagrams on the Parts Select web site is what made it easy for me. I could see from the diagram how the dryer was assembled. I removed the two screws holding the top on then separated the front apart from the drum. I did have to remove the panel in the back where the power connects to access the drive pulley and belt tensioner. I slid the old belt off and simply reversed the procedure for the new one. Put it back together and it runs beautifully.
I also installed a new door gasket with no tools. Now it does not leak lint from the fronf door.
When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!
Dryer not heating. When moving it away from wall it was sparking badly where the cord hooks up.
Removed case parts to expose internal wiring. Vacuumed up various types of mouse debris and plugged hole they were using. Ordered terminal block to replace the one that melted while sparks were flying. Replaced power cord with one I had in my basement from some other appliance that died a while ago. "Hey honey, ya know those old parts I saved..." :) Now it is heating to capacity and no spark-show! Oh yeah, the part I ordered from Partselect.com was delivered to my door the next day!!!!! Wow!
I wanted to fix the cheapest possible problem first which was the thermostat.
Got the dryer apart and it was the wrong thermostat for the dryer, which was good news! I looked in inside floor of the dryer cabinet and saw alot of tiny "springs". Couldn't figure how they got there.
Turned out they were coils from the heating element. Must have burnt out and fell free from the element. So I ordered that and replaced it.
I want to say that I'm in NJ and I ordered that thermostat and got it in ONE DAY! Thought that was too good to be true but when I ordered the heating element THAT CAME IN ONE DAY!
I don't know what kind of people work in the shipping department but they are awesome! You really made the difference on this job.
So did the info on your website. I've never even seen a dryer apart before. It was a piece of cake thanks to you guys. You just saved me about $500.
1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.
Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!
I was cleaning my laundry room when I noticed the gasket needed cleaning. While wiping it off it appeared as though I could remove it and that was my biggest mistake. Once removed it could not be replaced, due to the little parts that held it to the door began tearing off as I tried to put it back on. I ordered a new gasket and had it put on. It did not require any tools, just concentration. I've learned "if it's not broken, don't fix it"! I spoke with several other people and I am the only one who has removed a gasket. Thank you very much PartSelect for your help.
I followed the instruction of the first posting for this category and it worked perfectly...thanks for the nice detail...
- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model) - Loosened Top panel screws (2) from inside door area - Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating) - Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that - Removed old Drum Bearing - Vacuumend interior of dryer cabinet (especially area leading down to vent) - Snapped new Drum Bearing into place - Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely - Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secure