NBXR453EV0WW Hotpoint Dryer - Instructions

Snaped the new handle back on...no tools needed,
just fit the plastic groves of the handle into the holes on the dryer door. Very simple!

Removed top cover by removing 2 screws in front door opening. Then removed front door removing 2 screws, one on each inner side of the front door.
Removed 2 screws on side doors located about 9 inches from bottom of dryer to permit taking off drum. Slip off belt and remove drum.
Thinking I had a bad bearing, I decided to turn the dryer on and found out I had a bad motor-still functional but noisy. I had difficulty installing the new belt since there was not access panel (which was mentioned in the service manual), so I decided to take off the left side panel-about 8 screws. With the left side panel off, it was a lot easier to install a new belt and install the new front bearings. I actually did not fix the noise, since I need to replace the motor ($$$). When it goes really bad, I can order it then, and it should not take me long to replace it.

First I removed the two screws on the underneath side in the door at the top and removed the old drum bearing and installed new one with the 2 new plastic slide bearing. It was easy and I will tell all of my friends and family about the website. Service was fast and simple to order the right part. Thank you.......Linda

just put new one on. no tools needed fits in holes already there. handle just snaps on,

This one is so easy my grandson could do it. The removal was easy, it broke off. The installation was a "snap in place". Thinking I needed a few days of dryer use without the handle, I made a temporary repair. I fished some heavy packing string thru the slots in the door, made a loop, than a knot. This gave my wife something easy to grab to open. Did not even need to do the temporary repair, the part arrived in one day.

As soon as the new door handle arrived, I just snapped it into place. It took about two seconds>

I just snapped the door handle on the dryer in less than a minute. I am completely satified. Did I mention I received my part in one day. I ordered online before 3pm and received it the next day before 11am. Very impressed. Thanks PartSelect!!!

I broke the handle

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

When I first ordered the part, I did not know I needed 4 slides for the bearing. 2 of my slides had disintegrated. Make sure you have 2 good white slides, and 2 good blue slides, or order them with the bearing, or you will pay another $7.50 for shipping.
Once I got all of the parts and put it together using only common sense, I found it was binding tight. So I realigned the back of the drum that I had messed up while I was trying to diagnose the problem.
Parts Select definitely helped with diagnosis, through this comment section.
Thanks!

First I removed the front and top panel to the dryer. I then popped of the drum bearing, popped the new one on, added slides and put the top and sides back on. Turned on the dryer and it works just like new. All for less than a repair man would come out on a call for.

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

This repair was SO easy, it took less than 5 minutes. All I had to do is snap the door handle into the slots and it was finished. "Piece of Cake"!

The door to the clothes dryer would not open without the handle. To be able to use the dryer I secured the handle in place with packaging tape. The Part Select website made it extremely easy to identify the replacement part using just the model number. I placed the order on Thursday afternoon and received the part on Friday morning. I had to twist the broken handle to remove it from the door. Then I was able to snap in the replacement handle back in place with little force. Thanks to Part Select my problem was easily rectified.

First with a screwdriver,I removed the two screws and lifting the top and the front panel of the dyer off. The worn parts were easily removed and the new parts just snapped into place. I then just put the front and top panels back on and the whole job took less than 20 minutes to complete. The next day I received a letter from GE that the warranty would expire and would I like to buy an extention. Thanks to PartsSelect I saved a lot doing it myself.