MSD2454GRW Maytag Refrigerator - Instructions

Followed your video instructions and tips. Real easy

Getting the old ice maker out was not difficult - it sits on a small ridge built into the freezer and then it takes three screws to attach it to the side of the refrigerator. Three important things to remember: (1) take off the metal bar that shuts off the ice maker from the old part, the new part doesn't come with the bar; (2) keep the screws and the cap from the old ice maker as they don't come with the replacement part either; and (3) make sure you put the water tube back into the holder otherwise it will pour all over the freezer (and not into the ice tray).

unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.

Located the relay for compressor and took it apart and shook the relay and it rattled so I knew it must have been that. Also changed the run capacitor just to be safe. Works like a charm now.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

First Remove ice holder, now take out nut left side under tray, remove tray from mounts, unplug wires, remove tray from freezer, remove solenoid assy from tray try to keep it from coming apart, remove motor from tray, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). i used a small Chanel lock to hold shaft when removing yoke, Now remount the motor and yoke, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, remount it rest of the way in, install the nut. and your good to go.

After receiving the parts to repair the ice door, I replaced the solenoid and new chute door without problem. Then a problem I had been experiencing for well over a year, re-emerged. No Ice! I realized the icemaker was old, over 12 years and that the Teflon within the wells as well as the contacts for the timer were well worn. The ease of finding parts and the instructions provided by PartSelect, (written, video and users), I would attempt the replacement of the Ice Maker. When I examined the Freezer, I also identified that the Ice Maker shelf and enclosure (where the auger that drives the ice) was broken and barely hanging in place. I quickly identified the additional parts and ordered them. The total repair took about 60 minutes. and was treated to the sound of ice dropping into the bin by early evening. I am very pleased with the service, the quality of the products and the helpful hints from fellow users. I have added PartSelect to my IE favorites and it will be my first stop when I need repairs for any of my appliances.

I wasn't sure about the part I needed so I called the service number, they help me decide on the correct parts for my unit. This was the easiest repair I've ever done. One hex head screw and one clip in electrical connection and we were done. It took less than 5 minutes and now it works like new, no more leaking water and plenty of ice.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

I simply followed the online instructions. Easiest repair job I have done. Once installed, which took about ten minutes, it was producing ice in less than two hours and is performing as it should. Had my frig not been a bottom freezer the installation would have taken less than five minutes. And to let everyone know, the on line instructions came in very handy during the removal process. Many thanks.

First I did the thermostat and then I did the temperature control valve and I think that did it I should of done the control knob first because the fan in the freezer would run continually and wouldn't even shut off manually with the switch but now it turns off so I happen its fixed

went to you tube and typed in model no and brand name and the video explained in simple terms how to replace the selector pad

I ordered the replacement parts on line and received it a few days later. Thought I'd wait till the weekend to install the new parts. I expected it to take longer so I waited. Boy was I wrong. The hardest part was unloading the top shelf of the freezer. And it took longer to go get the nutdriver. I should have put it in immediately. Thanks for the instructional video. Works like a dream NO LEAKS. Will use your services on other parts as needed. Don from Pittsubrgh, PA.

Followed video advice

just had to remove the fan motor the hard thing is getting down to it