MMV5208WB1 Maytag Microwave - Instructions

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

slide into place under hood

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

But something dirrect on the glass it was cold and when the microwave stopped the glass broke. Got on the internet order a new glass on Sat. it was shipped on Monday and we received it on Friday. Thank you for your great service.

Replaced light bulb.

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

This is an over stove top mounted oven. Remove oven from mount and place on a work surface with padding to support the lamps and vent holes. Strip the case off and locate the noted other "most likely" parts. Watch out for the Capasitor. Read the test note available for each part; Diode, Thermister Fix, Capasitor and Magnitron. Do the test checks. My issue wasn't obvious because I think the Capasitor was discharged and needed to be hot to check the Magnitron. (I'm not an electrical engineer so...) At this point I did the foolish thing...I plugged the unit in and ran it. Watching from a distance I saw sparks fly from the top side of the Magnitron with the same result from my cup of water (cold-no sprks here.) I replaced the diode and tried again, same result. I ordered the Mag and the Thrmst-Fix. Thrmst-Fix was on BO when the Mag got here so I installed the part. Had to remove several pieces to afford room to work and still had to stretch and pry to get the old out and new in. Mag is held in place with Torx screws so check that before you start. No other tool works. Mag was the problem for this unit. Some problems encountered: Parts and pieces were quick in arriving as long as they were not Back Ordered. Be careful to follow a thread for your product to order parts. These review/instructions are mixed for simular appliances and sometimes lead off to other part lists and numbers. Prices differ from model to model, list to list and the part numbers change. Go back to your product and then trace for the correct parts. I noted a $40 price dif.between Magnitrons from simular part lists. When you receive the part check to match the part numbers, Manuf. no. are different from the Part Select No. but can be crossed. Otherwise using this site's instructions, checks, insulated tools, big rubber gloves and a face shield I managed to save a $600 machine from the junk pile. Parts as ordered were recieved and return of un-touched parts were accepted by Parts Select without unexpected hassle. Thanks for a positive experience.

For grease filter, just slipped it in outside area. For charcoal filter, unscrewed the top of microwave and replaced existing filter, then screwed back the top.

Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one

My husband open the microwave and see the capacitor melted. He try to find the piece in store,but unfortunatly he didn't find any. I found the piece on the web and ordered it. My husband replaced the part easily. The microwave work very well.The microwave was to our friend. He did replace it by a new one. Now we have a new microwave with a fan.

Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.

Removed the glass cover and replaced the bulb. Very simple.

I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.

--simpley removed 2 screws, removed old filter--but had PLENTY of cleaning to do before putting in the new filter !My husband LOVES to cook and pan fry foods--it won't go that long before being replaced in the future!

Time to replace the charcoal filter