Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Very loud squeaking noise
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.
The bottom line is that the back removes easily. You should: 1. unplug and remove the exhaust shoot 2. remove the top per YouTube or other source 3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground 4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part 4. undo the clip that holds the vent tube (from the heating element) to the part 5. remove the screws that hold the part to the inside back (3?) and push it out of the way 6. remove the clips and remove the old part 7. reassemble in reverse order
I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.
Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.
This could not have been easier. The hardest part was tipping the dryer over on its' side. Instructions: 1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor. Insert leveling foot into the foot opening on the bottom of the dryer & screw in with fingers until it is difficult to turn. 2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level. 3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position. 4. Use a level, back to front & side to side, to determine if feet need further adjustment. 5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
I ordered this to repair my girlfriend's mother's dryer. But according to my luck, the day the part was to arrive, I suffered an small brain bleed that put me in the hospital for a couple of weeks. I had read the instructions and was able to explain it to my girlfriend who replaced it and got it all back going right!
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.