Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MHE11RDQ4 > Instructions

MHE11RDQ4 Roper Microwave - Instructions

All installation instructions for MHE11RDQ4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MHE11RDQ4
16-30 of 38
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace vent grill

  • Customer: James from Naples, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed the old grill, including the three screws. I put the new grill in and screwed it in place.

Broken vent grille

  • Customer: Karen from Highlands Ranch, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Just screwed in the new one which fit perfectly!

Burned out light bulb which lit the surface of the range.

  • Customer: Michael J from LORAIN, OH
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

Cracked lower shelf

  • Customer: Bert from Naples, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Found correct part number, ordered, then installed.
Ordering was quick and easy. Delivery of shelf was very fast.
Very satisfied with everything.

Ceramic Tray had cracked

  • Customer: Rajendra from Rochester Hills, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Simple slide the tray into the groove

grill vent broken

  • Customer: Wendy from Jacksonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Took the grill vent out of the box and installed it. It was harder getting it out of the box than putting it in. I have been waiting for almost 15yrs for a replacement. The old grill vent was taped to the microwave. The Whirlpool company wanted over $100.00 for the grill vent. I wish I had known about PartSelect years ago!!!!

Burnt Out Light Bulb Replacement

  • Customer: alfred from summerville, SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 29 people found this instruction helpful
Open compartment, installed bulb, closed compartment

Microwave would not cook

  • Customer: Scott from Mickleton, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

Replaced microwave grille vent

  • Customer: Carl from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed old vent and replaced it with 4 screws. The old one was very greasy and could not be cleaned. Mew vent fit perfectly. Thank You

Replacement of hood light bulbs

  • Customer: Jerry from Pine, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

Microwave worked intermittently

  • Customer: Robert from Palmer Lake, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

2 burned out bulbs under the microwave/important light source for kitchen stove.

  • Customer: Ferol from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Motor quit working but light and timer still worked.

  • Customer: Thais from La Grange, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

Burned out light bulb

  • Customer: Ray from Gatlinburg, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced light bulb.

Original seal tape had released and the glass was very dirty

  • Customer: Sharon from FOLLY BEACH, SC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the old seal tape, took the door apart and cleaned the glass. Put the door back together and replaced the seal tape with the new seal and it looks like new. Watched a video on line on how to take apart the microwave door and it was very easy.
All Instructions for the MHE11RDQ4
16-30 of 38