MFI2568AEW Maytag Refrigerator - Instructions

Removed the fruit and veggie drawers & the deli (pantry) drawer. (Tim from Littleton CO helped me in this when he described his experience)......what helped me this time is before I put the side panel all the way into its' home position, I fastened the deli lid in place, being sure to not put any strain on the tab that I broke the last time. This go around I ordered two of these side panels just in case. I received my parts in two days. thanks!!!

Grind rivet head off , install rivet tap end

After unplugging the refrigerator, I removed the lower rear access panel that exposed the condenser and the overload/relay start capacitor with 1/4" nut driver (6 total). Next, I unplugged the wire harness and spring loaded keeper with needle nose pliers. Then I pulled the overload/relay start capacitor out of the 3 pronged male receptor located on the side of the condenser and plugged in the new one. Replaced the keeper, plugged the harness back in, and replaced the panel. Very easy fix.

Removed veggie draws and glass tray.

Part arrived in 2 days. Repair very easy

Ordered new center rail which arrived next day (!) my husband took the shelf out, inserted new rail into slots, replaced shelf, put the bins back and it works perfectly again. No problem at all, took less that 15 min. including removing food items from shelf and putting shelf back into the refrigerator.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

Simply remove the filter and insert the bypass cap in its place. Cap turned a little hard but if your careful everything goes together easily.

The large pull out full width drawer cover hinge pin broke off on the left side. The repair is easy with just two tools, a 1/4" nut driver and a phillips head screw driver. I removed the two conventional drawers that sit above the wide drawer with the broken hinge. Next lift out the glass divider that sits on top of the wide drawer and set it aside and remove the two braces front and back by lifting them out of their respective grooves. Remove the wide drawer with the lid by pushing in on the two black clips on each side of the drawer slide up towards the front and pull entire drawer out while putting pressure on the two clips at the same time. The drawer should come out leaving the drawer slides behind. Unscrew the 1/4" hex screws on the broken side panel using the nut driver and gently pull the side panel straight back toward you. Remove the drawer slide from the broken piece by unscrewing the two phillips head screws and rescrew the drawer slide onto the new side panel. Replace everything in reverse order. One note: do not use too much torque on the screws when replacing the parts as they only screw into plastic, this will avoid them stripping out. A snug fit is all you're after. There now, go pop a beer and sit down and relax, you are now a refrigerator repair man!

So simple I couldn't believe it! Twist out the old filter then twist in the new! Easy Peasy!

Remove two upper trays. glass shelf and shelf brackets. Remove bottom tray. unscrew side with back vent openings and remove with humidifier controls attached. Carefully remove control arms and back vent cover. Install on new unit and screw back in place. Check to make sure hinge pin lifts drawer top properly.

This was a very simple repair. It took longer to remove the crisper bins than it did to repair the pantry end cap.

A few screws out and in. and the rail just clipped in under the glass

I fortunately found the Part Select web site!! Used the trouble shooting guides and diagrams to diagnose the likely problem. Viewed the installation videos provided on the site and followed the procedure to complete the repair in about 15 minutes. It was a snap (actually three snaps) Fridge now working like new!! Thanks for the great information, guidance, pricing and superfast delivery!! Ron

removed drawers and glass; removed screws from end cap. removed screws from metal drawer runner. popped end cap off. reinstalled new end cap; attached metal drawer runner; cleaned everything and put glass back in as well as drawers. sweet